740410
15
Zoom out
Zoom in
Previous page
1/20
Next page
4
Select a zone.
5
Select MORE.
6
Select one or more options:
To limit the maximum volume output of this zone, select
VOLUME LIMIT, and adjust the level.
To set the subwoofer level for this zone, select SUB
LEVEL, and adjust the level.
To adjust the right and left speaker balance of this zone,
select BALANCE, and adjust the balance.
Power Options
Select , select the name of the stereo, and select SETTINGS
> POWER OPTIONS.
SYSTEM OFF: Sends a signal to turn off on all devices
connected to the network.
Network Settings
Select > SETTINGS > NETWORK.
DHCP CLIENT: Sets the device as a DHCP client. This is the
default setting for all devices that are not configured to be a
DHCP server or wireless access point.
STATIC IP: Allows you to set a static IP address for the device
(Setting a Static IP Address, page 11).
GARMIN MARINE NETWORK: Allows the device to be used on
a Garmin
®
Marine Network so it can be viewed and controlled
by connected Garmin chartplotters (Configuring the Stereo
for use with a Garmin Marine Network, page 11).
DETAILS: Shows information about the network configuration.
SAVE: Allows you to save changes to the network settings.
Setting the Stereo as the DHCP Server
If you connected more than two network devices together
directly or using a network switch or wireless access point and
did not install a router, you should configure only one Fusion
PartyBus stereo to be a DHCP server.
NOTE: Although the Fusion PartyBus can communicate with
each other without a DHCP server on the network, the devices
take longer to connect to each other when you first turn them on.
It is highly recommended to have a properly-configured DHCP
server on the network for the best results.
1
Select > SETTINGS > NETWORK > STATIC IP > SAVE.
You must set the stereo to use a static IP address before you
can set it as a wired DHCP server.
2
Select ADVANCED > DHCP SERVER > DHCP ENABLED >
SAVE.
You can configure the IP address range of the DHCP server
(DHCP Settings, page 11).
Setting a Static IP Address
If the stereo is configured as a static IP, it is automatically
assigned the IP address of 192.168.0.1. You can change this IP
address.
If the stereo is a DHCP client on the network and you do not
want the DHCP server to automatically assign an IP address to
the stereo, you can set a static IP address.
NOTE: Every device on the network must have a unique IP
address. If you select a static IP address that is the same as the
IP address on the network, the devices will not work properly.
1
Select > SETTINGS > NETWORK > STATIC IP.
2
Select an option:
To set the IP address, select IP, and enter the IP address.
To set the subnet mask, select MASK, and enter the
subnet mask.
NOTE: The subnet mask must match all other devices on
the network to work properly. A typical subnet mask is
255.255.255.0.
To set the default gateway IP address, select GATEWAY,
and enter the gateway IP address.
NOTE: The default gateway is typically set as the IP
address of the DHCP server on the network.
3
Select SAVE.
DHCP Settings
Select > SETTINGS > NETWORK > ADVANCED > DHCP
SERVER.
DHCP ENABLED: Sets the device as the DHCP server on the
network.
START IP: Sets the first IP address in the IP-address range of
the DHCP server.
END IP: Sets the final IP address in the IP-address range of the
DHCP server.
Configuring the Stereo for use with a Garmin Marine
Network
You can connect this stereo to a Garmin Marine Network in
order to view and control the stereo using a compatible Garmin
chartplotter.
NOTE: When you configure the stereo for use with a Garmin
Marine Network, you are limited to using only Garmin and
Fusion devices. You cannot use third-party routers, phones,
storage devices, or other network products with this stereo.
Select > SETTINGS > NETWORK > GARMIN MARINE
NETWORK.
Resetting Network Settings
You can reset all network settings for this stereo to the factory
default values.
Select > SETTINGS > NETWORK > RESET > YES.
Update Options
Select , select the name of the device, and select SETTINGS
> UPDATE.
NOTICE
Do not turn off the device or disconnect the power during a
software update. Turning off the power during a software update
may cause the device to become unresponsive.
NOTE:
You should update the device software using a USB flash
drive.
If the stereo is connected to a wireless network, you can
update the software using the Fusion-Link app on a mobile
device.
The device may restart a few times when updating. This is
normal.
You can program only newer versions of software on the
device.
STEREO: Updates the stereo.
NRX REMOTE: Updates an optional NRX remote connected to
the NMEA 2000 port or NMEA 2000
®
network using a valid
software update file on a connected USB flash drive.
ERX REMOTE: Updates an optional Apollo ERX400 remote
connected to the ETHERNET port or the Fusion PartyBus
network using a valid software update file on a connected
USB flash drive.
DAB MODULE: Updates an optional DAB module connected to
the SIRIUS XM port using a valid software update file on a
connected USB flash drive.
General Settings 11
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion Apollo MS-WB670 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion Apollo MS-WB670 in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fusion Apollo MS-WB670

Fusion Apollo MS-WB670 Installation Guide - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info