648605
51
Zoom out
Zoom in
Previous page
1/62
Next page
Doc. P/N: WSP-009-004
Version: V1.3
Issue Date: August 2013
www.wassp.com
Page 51 of 62
Operator Manual
7.4 When I run WASSP, it displays an error message - what does it
mean? Is my WASSP system faulty?
Consult the list below for the cause/course of action if an error message is displayed in WASSP.
7.4.1 GUI MESSAGES
7.4.1.1 Faults
F:0002: BAD COMMS TO RECEIVER BOARD (%s)
%s => module detecting error.
The communications link between the receiver board and Mity Carrier board has experi-
enced interference. This may be in the form of noise on the data line.
The System will attempt to recover by resetting the Receiver board.
This may be accompanied by the BTxR’s LED turning orange.
F:0003: TRANSMITTER UNDER VOLTAGE SET (STATUS = %lx) (%s)
%lx => status bits from transmitter board
%s => module detecting error
This message will occur when the voltage on the transmit board has not reached the re-
quired level for a transmit ping pulse.
Is the system has been reset by another fault then the transmit board may be disabled, re-
sulting in the under voltage error.
If this error does not get cleared (see below), check the PSU max current.
Check that it is not a secondary problem due to the BTxR resetting caused by an unrelated
event.
F:0004: TRANSMITTER UNDER VOLTAGE CLR (STATUS = %lx) (%s)
%lx => status bits from transmitter board
%s => module detecting error
This is a message informing the user that the voltage of the transmit board has reached the
required level, and is no longer under-voltage.
This will only occur after the above error.
F:0007: DRIVER REFUSED TO PING: UPP NOT READY (delta %0.6fsec) (%s)
%0.6f => time since last ping attempt
%s => module detecting error
A ping has been requested from the controller before the BTxR has dealt with the current
ping.This is usually a result of a timeout, potentially because the carrier board has not re-
ceived a full ping’s worth of data, possibly due to bad ribbon cable (see F:0002).
F:0008: DRIVER REFUSED TO PING: BAD TX BOARD STATUS(delta %0.6fsec) (%s)
%0.6f => time since last ping attempt
%s => module detecting error
A ping has been requested by the controller and refused, due to bad transmit board status
(e.g. under voltage).
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno WMB-3250 Wassp at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno WMB-3250 Wassp in the language / languages: English as an attachment in your email.

The manual is 10,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info