522136
41
Zoom out
Zoom in
Previous page
1/47
Next page
34
4.6 Optional Water
Temperature/Speed
Sensor
Water temperature/speed sensor
ST-02MSB and ST-02PSB, which are
designed for thru-hull mounting, are
optionally available. Install them as shown
below.
Mounting considerations
Choose a suitable mounting location
considering the following:
Choose a place free from vibration.
Choose a mid-boat flat position. The
sensor does not have to be installed
perfectly perpendicular. The sensor must
not be damaged in dry-docking
operation.
Choose a place apart from equipment
generating heat.
Choose a place in the forward direction
viewing from the drain hole, to allow for
circulation of cooling water.
1. Dry-dock the boat.
2. Make a hole of approx. 51 mm diameter
in the mounting location.
3. Unfasten locknut and remove the
sensor section.
4. Apply high-grade sealant to the flange
of the sensor.
5. Pass the sensor casing through the
hole.
6. Face the notch on the sensor toward
boat’s bow and tighten the flange.
7. Set the sensor section to the sensor
casing and tighten the locknut.
8. Launch the boat and check for water
leakage around the sensor.
Locknut
Face "notch"
toward bow.
Flange Nut
Coat with
silicone sealant.
Brim
φ
77
51
123
Water temperature/speed sensor
ST-02MSB, ST-02PSB
4.7 Wiring
Refer to the interconnection diagram to
connect cables. Leave slack in cables to
facilitate checking and maintenance.
Establishing the ground
The ground wire (1.25sq or more, local
supply) should be as short as possible. The
ground for the signal line is isolated from
the chassis, however the power line is not
insulated. Therefore, to connect external
equipment whose positive polarity is
connected to the ground line, do not
connect the signal line ground to chassis
ground.
The signal line ground is isolated from the
chassis ground, however the power line is
not insulated. Therefore, when connecting
external equipment having positive ground,
do not ground the signal line to the chassis.
If excessive noise shows on the screen, the
ground may be inadequate. In this case,
attach a steel plate measuring 20 cm by 30
cm on the outside of the hull to provide a
ground point. Connect the ground wire
there. Use a “closed” type lug (
) to
make the connection at the display unit. Do
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno LS-6100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno LS-6100 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info