Manual Furuno LS-6100 (page 40 of 47) (English)

522136

Zoom out

Zoom in

1/47

Attaching the sensor to the bracket

1. If the retaining cover near the top of the

bracket is closed, open it by depressing

the latch and rotating the cover

downward.

Step 1 Step 2

Latch

Retaining

cover

Pivot

arm (2)

Slot (2)

Step 4

Step 3

Attaching the sensor to the bracket

2. Insert the sensor’s pivot arms into the

slots near the top of the bracket.

3. Maintain pressure until the pivot arms

click into place.

4. Rotate the sensor downward until the

bottom snaps into the bracket.

5. Close the retaining cover to prevent the

accidental release of the sensor when

the boat is underway.

Cable routing

Route the sensor cable over the transom,

through a drain hole, or thorough a new

hole drilled in the transom above the

waterline.

Never cut the cable or remote the

connector; this will void the warranty.

Always wear safety goggles and a dust

mask.

1. If a hole must be drilled, choose a

location well above the waterline. Check

for obstructions such as trim tabs,

pumps, or wiring inside the hull. Mark

the location with a pencil. Drill a hole

through the transom using a 19 mm or

3/4” bit (to accommodate the

connector).

2. Route the cable over or through the

transom.

3. On the outside of the hull secure the

cable against the transom using the

cable clamps. Position a cable clamp 50

mm(2”) above the bracket and mark the

mounting hole with a pencil.

4. Position the second cable clamp

halfway between the first clamp and the

cable hole. Mark this mounting hole.

5. If a hole has been drilled in the transom,

open the appropriate slot in the transom

cable cover. Position the cover over the

cable where it enters the hull. Mark the

two mounting holes.

6. At each of the marked locations, use a 3

mm or 1/8” bit to drill a hole 10 mm

(3/8”) deep. The prevent drilling too

deeply, wrap masking tape around the

bit 10 mm (3/8”) from the point.

7. Apply marine sealant to the threads of

the #6 x 1/2” self-tapping screw to

prevent water from seeping into the

transom. If you have drilled a hole

through the transom, apply marine

sealant to the space around the cable

where it passes through the transom.

8. Position the two cable clamps and

fasten them in place. If used, push the

cable cover over the cable and screw it

in place.

9. Route the cable to the instrument being

careful not to tear the cable jacket when

passing it though the bulkhead(s) and

other parts of the boat. To reduce

electrical interference, separate the

sensor cable from other electrical wiring

and “noise” sources. Coil any excess

cable and secure it in place with zip-ties

to prevent damage.

www.Busse-Yachtshop.de email: info@busse-yachtshop.de

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Furuno LS-6100 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Furuno LS-6100 Manual

Product: