28260
39
Zoom out
Zoom in
Previous page
1/63
Next page
28
Connections
Only the signal cable runs from the display
unit to the antenna unit. Make the hole for
passing the cable through the bulkhead or deck
at least 20 millimeters diameter. In order to
minimize the chance of picking up electrical
interference, avoid where possible routing the
signal cable near other onboard electrical
equipment. Also, avoid running the cable in
parallel with power cables. Pass the cable
through the hole and apply sealing compound
around the hole for waterproofing.
The procedure for connecting the signal cable
to the antenna unit is as following.
1. Through a pipe or waterproof cable grand
fitted on the wheelhouse top or bulkhead.
2. Unfasten four screws at bottom of the scan-
ner base to remove the cable gland assem-
bly.
3. Pass the signal cable through the antenna
base and the cable gland assembly (re-
moved in step 2.)
4-M4x10
CLAMP PLATE
PACKING
FLAT
WASHER
Figure 6-13 Passing the signal cable
through the antenna housing
4. Fasten the cable gland assembly.
5. Connect the lead wires to RTB-9100 in the
antenna housing by referring to the Inter-
connection Diagram. Fasten the ground
washer at the bottom of the antenna hous-
ing as shown in Figure 6-13.
GROUND WIRE
Fasten
shield here.
RTB-9100
Figure 6-14 Connection in the antenna
housing
2. Detach the antenna housing cover from the
antenna housing by loosening four fixing
bolts. The antenna housing cover fitted with
the transceiver module can be stored in a
convenient place until the wiring to the an-
tenna unit is done.
3. Place the antenna housing on the mount-
ing platform and orient it as shown in Fig-
ure 6-11.
Ship's
bow
Ship's
bow
Figure 6-11 How to orient the antenna unit
4. Insert four M12 x 60 hex head bolts with
the seal washers from inside the antenna
housing, to prevent the bolts from contact-
ing the transceiver module. Install the seal
washer with the larger diameter next to the
head of the bolt. Coat flat and spring wash-
ers and nuts and then use them to fasten
the antenna housing to the mounting plat-
form. Finally, coat exposed parts of nuts,
bolts and flat and spring washers as shown
in Figure 6-12.
Note: Tighten the bolts by their nuts to pre-
vent damage to the seal washer. Do not turn
the bolts to secure the antenna housing.
Hex head bolt
(M12 x 60)
Seal washer
Silicone
sealant
Flat washer
Spring washer
Hex head nut
Scanner
housing
Figure 6-12 How to mount the antenna
housing
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1832 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1832

Furuno 1832 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info