28260
37
Zoom out
Zoom in
Previous page
1/63
Next page
26
Radome cover
Figure 6-2 Antenna unit
Mounting platform
Holes for antenna unit:
The mounting surface must be parallel with
the waterline and provided with five holes
whose dimensions are shown in the outline
drawing attached at the end of this manual.
The unit is adjusted so a target echo returned
from the bow direction will be shown on the
zero degree (heading line) position on the
screen. When drilling holes, be sure they are
parallel with the fore and aft line.
3. Prepare a platform of 5 to 10 millimeters
in thickness for the antenna unit. (A mount-
ing bracket for mounting the antenna unit
on a sailboat mast is optionally available.
See the below for details.) Find the cable
entry on the radome base. Next, position
the radome base so the cable entry faces
the stern direction. This alignment must be
as accurate as possible. Fasten the radome
base to the mounting platform with four
each of M10 x 25 hex bolts, flat washers
and spring washers.
Type: OP03-92
Code no.: 008-445-070
Figure 6-3 Assembling the sailboat mast
mounting bracket (option)
Mask size;
φ70 to φ125 mm
SHIP'S BOW
CABLE
ENTRY
4-Ø12 HOLES
PLATFORM
FLAT WASHER
SPRING WASHER
M10 X 25 HEX BOLT
Flat
washer
Spring
washer
Platform
Antenna base plate
M10 x 25
Hex bolt
Radome
5 - 10 mm
Apply silicone sealant
Effective
thread length
25 mm
Packing
Figure 6-4 How to fasten the radome base
to the mounting platform
Wiring and final preparation
4. Drill a hole of at least 20 millimeters di-
ameter through the deck or bulkhead to run
the signal cable between the antenna unit
and the display unit. (To prevent electrical
interference avoid running the signal cable
near other electrical equipment and in par-
allel with power cables.) Pass the cable
through the hole. Then, seal the hole with
sealing compound for waterproofing.
5. Remove the shield cover in the radome.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1832 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1832

Furuno 1832 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info