28260
38
Zoom out
Zoom in
Previous page
1/63
Next page
27
10. Attach the EMC core supplied as shown
below.
J806
J805
J803
J804
J802
J801
Motor
J613
J611
J1
EMC core
E04SS251512
(Above cable
clamping
plate)
Cable
entrance
IF9214
PTU-9335
MD9208
Cable
clamping
plate
Figure 6-8 How to attach EMC core
11. Fix the shield cover. Do not pinch the
cable.
12. Attach the radome cover, aligning triangle
mark on radome cover with that on ra-
dome base.
Radome cover
Radome base
Figure 6-9 How to position the radome
cover
13. Loosely fasten the radome fixing bolts.
You will tighten them after confirming
magnetron heater voltage.
Mounting (Model 1932, 1942)
Figure 6-10 Typical antenna unit mounting
locations
1. Drill four fixing bolt holes (13 millimeters
dia.), one cable entry hole (approx. 50 mil-
limeters dia.) in the mounting platform. See
the outline drawing.
6. Remove the cable clamping plate by un-
fastening four screws and removing a gas-
ket.
Shield cover
Shield cover
Pan head
screws
M4x8 7 pcs.
Pan head
screws
M4x8 7 pcs.
Pan head screws
M4x8 4 pcs.
Gasket
Cable clamping plate
Figure 6-5 Antenna unit, inside view
7. Pass the cable through the hole at the bot-
tom of the radome base.
8. Secure the cable with the cable clamping
plate and gasket. Ground the shield and
vinyl wire by one of the screws of the cable
clamping plate.
9. Connect the wire to the RF unit.
to one of the screws
of the cable clamping plate
9-pin connector:
to J801 on MD-9208
4-pin connector:
to J802 on MD-9208
13-pin connector:
to J611 on IF-9214
Figure 6-6 Signal cable, antenna unit side
J802
J801
J611
MD-9208
IF-9214
PTU-9335
Cable
entry
Figure 6-7 RF unit
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1832 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1832

Furuno 1832 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info