Manual Funai LDD-B2006 (page 8 of 32) (English)

503756

Zoom out

Zoom in

1/32

8 EN

Set up for Use

• Unless stated, all operations described are based on remote control

use. Some operations can be carried out using the buttons on the

control panel.

Language Selection

If you want to change the language of the on-screen menu, follow the

procedure below.

1) Connect the power cord to a standard AC outlet.

Note: • If some digits appear in the corner of the screen, press

STANDBY-ON without unplugging the power cord.

2) Press STANDBY-ON to turn on the TV.

3) Press SETUP so that the menu display appears on the TV screen.

4) Press Cursor K / L to point to “INITIAL”, then press

ENTER.

5) Press Cursor K / L to point to “LANGUAGE”, then press

ENTER.

6) Press Cursor K / L repeatedly to select your desired language,

then press

ENTER .

• The selected language will be indicated by yellow.

7) Press SETUP to exit.

Automatic Channel Presetting

You can programme the tuner to scan only the channels that you can

receive in your area.

1) Press STANDBY-ON to turn on the TV.

2) Press SETUP so that the menu display appears on the TV screen.

3) Press Cursor K / L to point to “INITIAL”, then press

ENTER

4) Press Cursor K / L to point to “CH TUNING”, then press

ENTER

• On DVD mode, this function is not available.

5) Press Cursor K / L to point to “AUTO”, then press ENTER.

• The tuner scans and memorises all the active channels in your area.

When “AUTO” is completed, the lowest memorised channel

reappears on the screen, and you can use

PROG. +/

on the

control panel or

/ (prog.) on the remote control for the

memorised channels.

• If you press

SETUP during the scanning, this operation will stop

and the lowest memorised channel will appear on the TV screen.

Manual Channel Presetting

You can preset a channel manually and individually.

1) Follow the steps 1) to 4) in the “Automatic Channel Presetting”.

2) Press Cursor K / L to point to “MANUAL”, then press

ENTER

3) (Only for LDD-C2006)

Press

Cursor K / L to point to “SYSTEM”, then press ENTER

to display the desired system.

4) Press Cursor K / L to point to “POSITION”, then press

ENTER

5) Press the Number buttons or Cursor K / L to select your

desired position number, then press

ENTER

• You can select position number 01-99.

• If “ON” appears on the right side of “SKIP”, press

Cursor K / L to point to “SKIP”. Then, press ENTER to

select “OFF”.

• If you want to remove scrambled signals, press

Cursor K / L repeatedly to point to “DECODER”. Then,

press ENTER to select “ON”.

6) Press Cursor K / L to point to “CHANNEL”, then press

ENTER

7) Press Cursor K / L to start scanning.

• The tuner will begin to search up or down automatically.

When a channel is found, the unit will stop searching and the

picture will appear on the TV screen.

• You can select desired channel number by using

the Number buttons. You must refer to the following

Channel Plan table and press three digits to select the channel

number.

(To select channel 24, press “

0” button first and then press “2”

and “

4”.)

• If this is the channel you want, press ENTER.

This unit can receive Hyper and Oscar frequency bands.

8) Press SETUP to exit.

Note: • To confirm that a channel has been added, press

/ (prog.).

• If you insert the RF cable plug into the Aerial input jack

after manual channel presetting, a picture will be distorted.

In this case, press

/ (prog.) to select the same channel

again.

TV OPERATION

(Only for LDD-B2006)

Sorting of TV channels from P01 to P05 will be performed

automatically as follows.

P01 : BBC1 P04 : CH4

P02 : BBC2 P05 : CH5

P03 : ITV

SETUP

BACK LIGHT [BRIGHT]

INITIAL

LANGUAGE

DEUTSCH

ENGLISH

ESPAÑOL

FRANÇAIS

ITALIANO

NEDERLANDS

SVENSKA

POLSKI

INITIAL

CH TUNING

LANGUAGE

SETUP

BACK LIGHT [BRIGHT]

INITIAL

CH TUNING

LANGUAGE

CH TUNING

AUTO

MANUAL

MOVE

AUTO

START FINISH

Channel Plan

TV Channel

Indication

PAL I PAL B/G SECAM D/K SECAM L

01–10

IRA–

IRJ,GAP

– – F1–F10

02–12 – E2–E12 –

13–20 –

A-H

(only ITALY)

––

21–69 E21–E69

74–78 X, Y, Z, Z+1, Z+2 –

80–99, 100 S1–S20, GAP –

71–86 – – – B–Q

90–106 – – – S4–S20

121–141 S21–S41

142–153 –

– R1–R12 –

SETUP

BACK LIGHT [BRIGHT]

INITIAL

CH TUNING

LANGUAGE

CH TUNING

AUTO

MANUAL

MOVE

MANUAL

POSITION

CHANNEL

DECODER

SKIP

P55

055

[OFF]

L4670EA(EN).fm Page 8 Tuesday, May 15, 2007 5:36 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Funai LDD-B2006 in the language / languages: English as an attachment in your email.

The manual is 1,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Funai LDD-B2006 Manual

Product: