560834

Friedland GlobalGuard Home Alarm System Manual

12
Zoom out
Zoom in
Previous page
1/232
Next page
12
5.7 Deleting the IP gateway from the control panel (optional)
1. Press the button.
2. Enter the 4-digit PIN code (User).
3. Press the button.
4. Select the program mode “5. COMMS”. The display shows “5-1 COMMS SETUP”.
5. Press the button. The display shows “Input (01-12) Device NO.”.
6. Enter the device number (0-12). Make sure that no other device is already linked to the channel.
7. Press the button.
8. Select the program mode “:4 DEVICE REMOVE”. The display shows “SELECT YES>*/ NO>#”.
9. Press the button.
5.8 Connection terminal block (optional)
1
Hardwired zone connections (closed contacts)
3
Not used
2
Hardwired zone connections (volt-free contacts)
4
Tamper switch (wired connection)
To access the connection terminal block, first put the system into test mode (refer to the section “Test mode (TEST MODE)”.
1. Set jumper link P1 to the off position.
2. Switch off the power supply to the power adaptor.
3. Remove the control panel from the wall bracket.
4. Disconnect the power adaptor from the control panel.
5. Remove the battery cover.
6. Remove and disconnect the backup battery.
7. Wire the connections to the terminals as required.
8. Connect and install the backup battery.
9. Install the battery cover.
10. Connect the power adaptor to the control panel.
11. Switch on the power supply to the power adaptor.
12. Install the control panel to the wall bracket.
13. Press the button to exit test mode.
The signaling contacts on all hardwired alarm and tamper zones must be volt free. i.e. they must only open and close and not
apply any self-generated voltage across the contacts. The contacts on zones 33, 34, 35 and the tamper circuit must be normally
closed. An alarm will be triggered when the contacts open. On zones 33, 34 and 35, additional door/window contact detectors
can be hardwired to these terminals. The contacts on zone 36 must be normally open. An alarm will be triggered when the
contacts close.
Note: Jumper link P51 must be normally in the off position. Set jumper link P51 to the on position only if the hardwired tamper
circuit is used.
5.9 Backward compatibility (security devices)
Earlier versions of 868MHz PIR movement detectors, door/window contact detectors, remote controls and remote keypads
devices are also compatible with the system. If you upgrade an existing 868MHz wireless security system, you can use the same
security devices by simply linking the security device to the GlobalGuard system.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland GlobalGuard Home Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland GlobalGuard Home Alarm System in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Friedland GlobalGuard Home Alarm System

Friedland GlobalGuard Home Alarm System Installation Guide - English, German, Dutch, French, Italian, Portuguese, Spanish - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info