775815

Fluke networks IntelliTone Pro 200 Manual

9
Zoom out
Zoom in
Previous page
1/21
Next page
Locating and Isolating Terminated UTP/STP Cables with the IntelliTone
5
To reactivate the toner or probe, turn the rotary switch to
any position except OFF.
Locating and Isolating Terminated
UTP/STP Cables with the IntelliTone
The IntelliTone Pro toner provides two toning modes for
locating and isolating cables: one digital tone and
the SmartTone analog tones (500 Hz to 1200 Hz) .
With the toner set to digital tone mode, the probe can be
set to either locate or isolate .
Both toning signals are available at all connectors on the
toner.
The digital tone is optimized for 4 pair UTP data
environments and the SmartTone analog tone is
optimized for two wire locating.
To locate and isolate cables using the digital tone, do the
following:
1
Connect the IT200 toner to a jack or punch-down block
as shown in Figure 1.
2
Turn the toner’s rotary switch to .
3
Turn the IP200 probe’s rotary switch to (locate).
4
Use the probe to find the general location of the tone
at a cable rack, patch panel, or behind a wall. The
SYNC LED lights up green when the probe is receiving
the IntelliTone signal.
In locating mode, the probe’s LEDs light up from 1 to 8
as the signal strength increases. The higher the
number, the stronger the signal.
Note
If you cannot locate the IntelliTone signal on
2-conductor cables, the cable may be shorted. Use
the cable map test (page 8) to test for shorts on
cables with RJ11 and RJ45 connectors. Use the
continuity test (page 12) to check for shorts on
coax and non-terminated cables.
5
Turn the probe’s rotary switch to (isolate).
6
Use the probe to isolate the tone source in the cable
bundle or at the patch panel. The SYNC LED lights up
green when the probe is receiving the IntelliTone
signal.
In isolating mode, the probes LEDs light up from 1 to 8 as
the signal strength increases.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke networks IntelliTone Pro 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke networks IntelliTone Pro 200 in the language / languages: English as an attachment in your email.

The manual is 0.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke networks IntelliTone Pro 200

Fluke networks IntelliTone Pro 200 Quick start guide - English, German, French, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info