531719
8
Zoom out
Zoom in
Previous page
1/20
Next page
GB
8
3. An adjusting pin and screw is used to ad-
just the tension of the chain. It is very im-
portant when assembling the bar , that the
pin located on the adjusting screw aligns
into a hole i n the ba r. Tu rning t he screw will
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
illustration below .
Adjustment located on clutch cover
Inside
view of
clutch
cover
4. Turn the adjusting screw by hand coun-
terclockwise until the adjusting pin just
touches the stop. This should allow the
pin to be near the correct position.
5. Slide guide bar behind clutch drum until
guide bar stops against clutch drum
spro cke t .
Guide bar
Bar bolts
6. Carefully remove the chain from the pack-
age. Hold chain with the dr ive links as
sho wn .
CUTTERS MUST F ACE IN
DIIRECTION OF ROTATION
Tip of
Bar
Cutters
Depth Gauge
Drive Links
7. Place chain over and behind clutch, fitting
thedrivelinksintheclutchdrumsprocket.
8. Fit botto m of drive links between t heteeth
in the sprocket in the nose of the guide
bar.
9. Fit chain drive links into bar groove.
10.Pull guide bar forward until chain is snug
in guide bar groove. Ensure all drive links
are in the bar groove.
11. Now, install clutch cover making sure the
adjusting pin is positioned in the lower
hole in the guide bar. Remember this pin
moves the bar forward and backward as
the screw is turned.
Clutch
Cover
Lower
Hole
Guide Bar
Adjusting Pin
12.Install bar nuts and finger tighten only .
Once the chain is tensioned, y ou will
need to tighten bar nuts.
CHAIN TENSION (Including units
with chain already installed)
WARNING: Wear protective gloves
when h andlingchain. The chain is sharp and
can cut you even when it is not moving.
NOTE: When adjusting chain tension, make
sure the bar nuts are finger tight only . Attempt-
ing to tension the chain when the bar nuts are
tight can cause damage.
Checking the tension:
Use the screwdriver end of the chain adjust-
ment t ool (bar tool) to move the chain around
the bar. If the chain does not rotate, it is too
tight. If too loose, the chain will sag below the
bar.
Chain Adjustment
Tool
(Bar Tool)
Guid
e
Bar
Adjusting
Screw
Bar Nuts
Adjusting the tension:
Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.
8


Need help? Post your question in this forum.

Forumrules
1

Forum

florabest-fbks-4014

Reset search

  • Looking for Spring attached to handle of chainsaw and attached down where you put the chain oil in. Submitted on 10-4-2020 at 19:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FBKS 4014 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBKS 4014 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Florabest FBKS 4014

Florabest FBKS 4014 User Manual - Dutch - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info