778621
17
Zoom out
Zoom in
Previous page
1/85
Next page
7.2 Changing gear [1-4]
Gear switch forwards (digit 1 visible) =
1st gear
Gear switch to rear (digit 2 visible) =
2nd gear
7.3 Adjust torque [1-2]
The marking [1-3] shows the selected position.
Drilling
Marking shows the drill symbol [1-1] = Maxi
mum torque.
Fastening
Torque corresponding to setting:
Position 1 = low torque
Position 12 = high torque
8 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
CAUTION
Risk of injury from hot and sharp tool
Do not use any blunt or faulty tools.
Wear protective gloves.
The PO numbers of the accessories and tools
can be found in the Festool catalogue or online
at "www.festool.co.uk".
8.1 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CEN
TROTEC tool chucks.
8.2 Chuck BF-FX10 [5]
For clamping drill bits and bits with max. shaft
diameter of 10 mm.
Clamp tool centrally in the chuck.
8.3 Angle attachment XS-AS [6]
(accessories) Drilling and screwdriving at right
angle to power tool.
You can engage the angle attachment
in 16 different angle settings.
8.4 Tool holder in the drill spindle [7]
Bits can be inserted directly into the hexagon
socket holder of the drill spindle.
9 Working with the power tool
WARNING
Risk of injury
Always secure the workpiece in such a
manner that it cannot move while being
machined.
9.1 On/Off switch [1-6]
Press = ON, release = OFF
The speed of the machine depends on
how far the on/off switch is pressed
in.
9.2 LED lamp with capacity indicator
The LED bulb [1-10] lights up when the ON/OFF
switch is pressed [1-6].
After releasing the ON/OFF switch [1-6] the ca
pacity indicator on the LED lamp [1-10] dis
plays the state of charge of the battery pack for
a few seconds:
100%
0%
70 - 100%
40 - 70 %
15 - 40 %
< 15 %
Recommendation:
Charge battery pack
before further use.
9.3 Bit depot [1-11]
Magnetic, for storing bits and bit holders.
9.4 Warning signals
Power tool shuts down, capacity indicator
flashes: Battery pack is empty.
Change the battery pack.
Power tool shuts down, capacity indicator does
not flash: Power tool is overheating or has been
overloaded.
Apply a lesser load to power tool.
Allow power tool to cool down.
English
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TXS - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TXS - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 2.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info