778621
15
Zoom out
Zoom in
Previous page
1/85
Next page
Safety instructions when using long drill bits
a) Never operate at higher speed than the
maximum speed rating of the drill bit. At
higher speeds, the bit is likely to bend if al
lowed to rotate freely without contacting
the workpiece, resulting in personal injury.
b) Always start drilling at low speed and
with the bit tip in contact with the work
piece. At higher speeds, the bit is likely to
bend if allowed to rotate freely without con
tacting the workpiece, resulting in personal
injury.
c) Apply pressure only in direct line with
the bit and do not apply excessive pres
sure. Bits can bend causing breakage or
loss of control, resulting in personal injury.
2.3 Machine-specific safety instructions for
battery pack and charger
This charger can be operated by persons
with reduced physical, sensory or mental
capabilities or a lack of practical experi
ence and knowledge, provided they are su
pervised or have been instructed to use the
machine safely and understand the dan
gers of machine operation. Children are
not allowed use or play with the machine.
Do not open the battery pack or charger.
Protect the charger from metal compo
nents (e.g. swarf) and liquids.
Do not use power adapters or battery
packs form other manufacturers to oper
ate the cordless power tool. Do not use
any charger from other manufacturers for
charging the battery pack. The use of im
permissible accessories may result in elec
tric shock and / or serious accidents!
Protect the battery pack from heat > 50 °C
or constant heat sources such as sunlight
or naked flames.
Never use water to extinguish burning Li-
ion battery packs; always use sand or a fire
blanket.
Check the plug and the cable regularly in
order to prevent a hazard. In the event of
damage, these must be replaced by an au
thorised service workshop only.
Always pull the mains plug out of the sock
et when the charger is not in use.
2.4 Emission levels
The levels determined in accordance with
62841 are typically:
Sound pressure level LPA = 63 dB(A)
Sound power level LWA = 74 dB(A)
Uncertainty K = 3 dB
CAUTION
Noise generated when working
Risk of damage to hearing
Use ear protection.
Vibration emission level ah (vector sum for
three directions) and uncertainty K measured in
accordance with 62841:
Fastening ah = < 2.5 m/s2
K=1.5 m/s2
Drilling in metal ah = 3.0 m/s2
K=1.5 m/s2
The specified emission levels (vibration, noise)
are used to compare machines.
They are also used for making preliminary
estimates regarding vibration and noise
load during operation.
They represent the primary applications of
the power tool.
CAUTION
The emission values may deviate from the
specified values. This is dependent on how
the tool is used and the type of workpiece
being machined.
The actual load during the entire operating
cycle must be evaluated.
Depending on the actual load, suitable pro
tective measures must be defined in order
to protect the operator.
3 Intended use
Cordless drill suitable
for screwing in and tightening screws,
for drilling in metal, wood, plastics and
similar materials.
Not intended for clamping tools other than
drills and drill bits, e.g. compass saws, stirring
rods, metal brushes.
Charger MXC suitable
for charging the listed battery packs.
only for indoor use.
The user is liable for improper or non-in
tended use; this also includes continuous
industrial operation.
English
15
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TXS - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TXS - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 2.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info