778530
29
Zoom out
Zoom in
Previous page
1/185
Next page
8.2 Acoustic warning signal
Acoustic warning signals sound and the ma
chine switches off in the following operating
states:
peep
Battery flat or machine
overloaded:
Change the battery
Reduce the machine load
8.3 Kickback stop function
WARNING
Risk of injury
The kickback stop does not guarantee com
plete protection against a kickback.
Always concentrate on your work and refer
to the safety instructions and warnings.
A kickback while working may cause the saw to
lift unintentionally.
The feeler wedge [8-1] detects unintentional
lifting (kickback) of the saw from the workpiece
or a rail during work and triggers the quick-act
ing braking of the saw blade (Fig. 8a).
This reduces the risk of a kickback. However, it
cannot be entirely ruled out.
KickbackStop function status LED
Colour Meaning
Green The KickbackStop function is ac
tive.
Orange The KickbackStop function is deac
tivated.
Flashing
orange The KickbackStop function is not
active.
The saw was started up before the
feeler wedge was pressed against
the workpiece or a guide rail. The
saw's plate is not positioned such
that it is completely level.
Once the saw has been positioned
such that is completely level, the
LED will switch to green. If this is
not the case, check the Kickback
Stop function (see Section 8.7)
Flashing
red The KickbackStop function has
been triggered.
8.4 Unintentional triggering of the kickback
stop function
Working without a guide rail on an uneven
workpiece may cause the kickback stop func
tion to trigger unintentionally (Fig. 8b).
The feeler wedge [8-1] runs along the work
piece. If there is a recess in the workpiece, the
position of the feeler wedge will correspond to
the position when the workpiece or guide rail is
lifted. This triggers the kickback stop function.
It may then be necessary to work without the
kickback stop function (see Section 8.6).
8.5 Procedure after the kickback stop
function has been triggered
Triggered by unintentional lifting (kickback)
Determine and eliminate any reasons for
lifting.
Check the machine for any damage.
Check the feeler wedge for any damage.
Check the KickbackStop function (see Sec
tion 8.7).
After the kickback stop function has uninten
tionally been triggered
Release the on/off switch and wait until the
kickback stop function status LED is no lon
ger flashing.
Check whether there was an unintentional
triggering of the kickback stop function (see
Section 8.4) or a kickback.
Try first to continue working with an active
kickback stop function. Only deactivate the
kickback stop function if you are working
without a rail and your workpiece is so un
even that the kickback stop function would
unintentionally be triggered several times
(see Section 8.6).
8.6 Working without the kickback stop
function
WARNING
Risk of injury
If the kickback stop function is deactivated,
the saw blade is not stopped when it unin
tentionally lifts.
Only deactivate the kickback stop function
if you are working without a rail and your
workpiece is so uneven that the kickback
stop function would unintentionally be trig
gered several times.
Deactivate the kickback stop function
Press the kickback stop function OFF but
ton.
English
29
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TSC 55 KEB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TSC 55 KEB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info