778530
27
Zoom out
Zoom in
Previous page
1/185
Next page
Colour Material Symbol
Yellow Wood
Red Laminate, mineral ma
terial
HPL/TRESPA
®
Green Plaster- and cement-
bonded chipboard and
fibreboard
Blue Aluminium, plastic
"$3:-
7.5 Changing the saw blade [5]
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
Remove the saw blade
Swivel the saw to 0° before replacing the
saw blade and adjust the maximum cutting
depth.
Turn the lever [5-2] as far as it will go. Op
erate the lever only when the saw is at a
standstill!
Push the saw unit down until it engages.
The saw unit is located in the upper locking po
sition [A].
Loosen the screw [5-8] using the Allen key
[5-2].
Remove the saw blade [5-7].
Cleaning the feeler unit
WARNING! Any contamination of the feeler unit
may impair the kickback stop function and
therefore prevent the saw blade from being
stopped.
Hold the saw unit securely by its handle,
close the lever [5-2] and press the saw unit
all the way down.
Release the lever [5-2] again and click the
saw unit into place.
The saw unit is located in the lower locking po
sition [B].
Clean the feeler unit [5-4] by blowing it out
or using a brush.
Inserting the saw blade
WARNING! Check the screws and flange for
contamination and only use clean and undam
aged parts.
Hold the saw unit securely by its handle and
turn the lever [5-2] as far as it will go.
Return the saw unit to the upper locking po
sition.
Insert a new saw blade.
WARNING! The direction of rotation of the
saw blade [5-6] and saw [5-3] must match.
Serious injuries may occur in the event of
non-compliance.
Insert the outer flange [5-5] in such a way
that the pulling peg engages in the recess
of the inner flange.
Tighten the screw [5-8].
Hold the saw unit securely by its handle,
close the lever [5-2] and guide the saw unit
back upwards.
7.6 Fitting the viewing window/splinter
guard
The viewing window (transparent) [6-1] pro
vides a view of the saw blade and optimises
dust extraction.
With 0° cuts, the splinter guard (green) [6-2]
also improves the quality of the cutting edge of
the sawn-off workpiece on the upper side.
Insert the splinter guard [6-2].
Screw the rotary knob [6-3] through the
long hole in the splinter guard.
Make sure that the nut [6-4] is seated se
curely in the splinter guard.
CAUTION! Only use the rotary knob sup
plied with your plunge-cut saw. The rotary
knob of another saw may be too long and
jam the saw blade.
Sawing a splinter guard
You must bed in the splinter guard before using
it:
Set the machine to maximum cutting depth.
Set the machine speed to 6.
Place the machine for sawing the splinter
guard on a test piece of wood.
English
27
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TSC 55 KEB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TSC 55 KEB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info