778530

Festool TSC 55 KEB Manual

28
Zoom out
Zoom in
Previous page
1/185
Next page
7.7 Dust extraction
WARNING
Health hazard posed by dust
► Always work with an extractor.
► Comply with national regulations.
► When sawing carcinogenic materials, al
ways connect a suitable extraction mobile
in accordance with national regulations. Do
not use the chip collection bag.
Independent extraction
► Secure the connection piece [7-2] of the
dust collection bag [7-3] at the extractor
connector [7-1] with a clockwise rotation.
► To empty, remove the connection piece of
the dust collection bag from the extractor
connector with an anti-clockwise rotation.
Blockages in the guard may impair safety fea
tures. To avoid blockages, it is therefore better
to work with a mobile dust extractor at full suc
tion power.
Static charge may occur when sawing (e.g.
MDF). If this is the case, work with a mobile
dust extractor and an antistatic suction hose.
Festool mobile dust extractor
A Festool mobile dust extractor with a suction
hose diameter of 27/32  mm or 36  mm (36 mm
recommended due to the reduced risk of clog
ging) can be connected to the extractor connec
tor [7-1].
The adapter on a 27 diameter suction hose is
inserted into the angle adapter [7-4]. The
adapter on a 36 diameter suction hose is inser
ted over the angle adapter [7-4].
CAUTION! A static charge may build up if no
antistatic suction hose is used. The user may
receive an electric shock and the power tool's
electronics may be damaged.
8 Working with the electric
power tool
When working on the machine, observe
all of the safety warnings that are listed
at the start as well as the following rules:
Before starting
– Before each use, check whether the drive
unit with the saw blade correctly and fully
swivels back up into its initial position in
the protective housing. Do not use the saw
if the upper end position is not secured.
Never clamp or secure the swivelling drive
unit at a specific cutting depth. This would
mean that the saw blade is not protected.
– Check the plunging mechanism prior to use
and do not use the machine if it does not
work correctly.
– Check that the saw blade is securely in
place.
– Before each use of the saw, check that the
KickbackStop is functioning properly (see
Section 8.7).
–CAUTION! Risk of overheating. Before use,
make sure that the battery pack is securely
clicked into place
– Make sure that the rotary knob [1-2] is
tightened before starting work.
– Make sure that the extractor hose does not
snag the entire saw cut, either on the work
piece, the workpiece support or hazards on
the ground.
– Always secure the workpiece in such a way
that it cannot move during machining.
– Position the workpiece so that it is stress-
free and level.
During work
– Position the saw's plate such that it is al
ways completely level during any work.
– When working, always hold the power tool
with both hands on the handles [1-1]. This
is a prerequisite for precise work and is es
sential for plunge-cutting. Plunge into the
workpiece slowly and evenly.
– Only guide the power tool towards the
workpiece when it is switched on.
– Always push the saw forwards [10-2], and
never towards yourself.
– Adapt the infeed speed to prevent the cut
ters on the saw blade from overheating and
prevent plastic materials from melting dur
ing cutting. The harder the material to be
sawn, the lower the feed speed needs to be.
– Make sure that the guard completely sur
rounds the saw blade before placing the
saw on the worktop or on the ground.
8.1 Switch on/off
Pressing the switch-on lock unlocks the plung
ing mechanism.
► Slide the switch-on lock [1-6] upwards and
press the on/off switch [1-7] (press = ON /
release = OFF).
The saw unit can then be moved downwards.
This causes the saw blade to emerge from the
protective cover.
English
28
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TSC 55 KEB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TSC 55 KEB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info