778502

Festool TKS 80 EBS Manual

30
Zoom out
Zoom in
Previous page
1/276
Next page
and balance. It should be installed in an
area that provides enough room to easily
handle the size of your workpiece. Cram
ped, dark areas, and uneven slippery floors
invite accidents.
–Frequently clean and remove sawdust
from under the saw table and/or the dust
collection device. Accumulated sawdust is
combustible and may self-ignite.
–The table saw must be secured. A table
saw that is not properly secured may move
or tip over.
–Remove tools, wood scraps, etc. from the
table before the table saw is turned on.
Distraction or a potential jam can be dan
gerous.
–Always use saw blades with correct size
and shape (diamond versus round) of ar
bour holes. Saw blades that do not match
the mounting hardware of the saw will run
off-centre, causing loss of control.
–Never use damaged or incorrect saw
blade mounting means such as flanges,
saw blade washers, bolts or nuts. These
mounting means were specially designed
for your saw, for safe operation and opti
mum performance.
–Never stand on the table saw, do not use it
as a stepping stool. Serious injury could
occur if the tool is tipped or if the cutting
tool is accidentally contacted.
–Make sure that the saw blade is installed
to rotate in the proper direction. Do not
use grinding wheels, wire brushes, or
abrasive wheels on a table saw. Improper
saw blade installation or use of accessories
not recommended may cause serious in
jury.
2.3 Further safety instructions
–
Wear suitable personal protective equip
ment: Ear protection, protective goggles,
dust mask for work that generates dust
and protective gloves for changing tools.
– Faults on the power tool, including the sep
arating guards or the tool, must be repor
ted to maintenance staff immediately. The
machine must not be used until the fault
has been eliminated.
– Check the plug and cable on a regular ba
sis and, if they are damaged, have them re
placed by an authorised customer service
workshop.
– Use of your own aids e.g. rulers, etc. is not
permitted.
–Only for AS/NZS: The tool shall always be
supplied via residual current device with a
rated residual current of 30 mA or less.
2.4 Safety instructions for the pre-
assembled saw blade
Usage
– The maximum speed specified on the saw
blade must not be exceeded and the speed
range must be adhered to.
– The pre-installed saw blade is only de
signed for use in circular saws.
– Proceed with extreme care when unpack
ing, packing and handling the tool (e.g. in
stalling it in the machine). There is a risk of
injury from extremely sharp cutting edges!
– When handling the tool, wearing safety
gloves provides a more secure hold of the
tool and further reduces the risk of injury.
– Circular saw blades with cracked bodies
must be replaced. Repair is not permitted.
– Circular saw blades with a combination de
sign (soldered saw teeth) with saw tooth
thickness smaller than 1 mm must no lon
ger be used.
–WARNING! Do not use tools with visible
cracks or blunt or damaged cutting edges.
Installation and mounting
– Tools must be clamped in such a way that
they cannot come loose during operation.
– When assembling the tools, it must be en
sured that the clamping takes place on the
tool hub or the clamping surface of the
tool, and that the cutting edges do not
come into contact with other components.
– Do not lengthen the key or tighten by hitting
with a hammer.
– The clamping surfaces must be cleaned to
remove contamination, grease, oil and wa
ter.
– Clamping screws must be tightened ac
cording to the manufacturer's instructions.
– Only securely installed rings, e.g. rings that
have been pressed in or those that are held
in position by an adhesive bond, may be
used to adjust the hole diameter of circular
saw blades to the spindle diameter of the
machine. The use of loose rings is not per
mitted.
English
30
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TKS 80 EBS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TKS 80 EBS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info