778502
29
Zoom out
Zoom in
Previous page
1/276
Next page
plug the tool then clear the jam. Jamming
the saw blade by the workpiece can cause
kickback or stall the motor.
Do not remove pieces of cut-off material
while the saw is running. The material may
become trapped between the fence or in
side the saw blade guard and the saw blade
pulling your fingers into the saw blade.
Turn the saw off and wait until the saw
blade stops before removing material.
Use an auxiliary fence in contact with the
table top when ripping workpieces less
than 2 mm thick. A thin workpiece may
wedge under the rip fence and create a
kickback.
3) Kickback causes and related warnings
Kickback is a sudden reaction of the workpiece
due to a pinched, jammed saw blade or mis
aligned line of cut in the workpiece with respect
to the saw blade or when a part of the work
piece binds between the saw blade and the rip
fence or other fixed object.
Most frequently during kickback, the workpiece
is lifted from the table by the rear portion of the
saw blade and is propelled towards the opera
tor.
Kickback is the result of saw misuse and/or in
correct operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
Never stand directly in line with the saw
blade. Always position your body on the
same side of the saw blade as the fence.
Kickback may propel the workpiece at high
velocity towards anyone standing in front
and in line with the saw blade.
Never reach over or in back of the saw
blade to pull or to support the workpiece.
Accidental contact with the saw blade may
occur or kickback may drag your fingers in
to the saw blade.
Never hold and press the workpiece that
is being cut off against the rotating saw
blade. Pressing the workpiece being cut off
against the saw blade will create a binding
condition and kickback.
Align the fence to be parallel with the saw
blade. A misaligned fence will pinch the
workpiece against the saw blade and create
kickback.
Use a featherboard to guide the workpiece
against the table and fence when making
non-through cuts such as rabbeting, dado
ing or resawing cuts. A featherboard helps
to control the workpiece in the event of a
kickback.
Use extra caution when making a cut into
blind areas of assembled workpieces. The
protruding saw blade may cut objects that
can cause kickback.
Support large panels to minimise the risk
of saw blade pinching and kickback. Large
panels tend to sag under their own weight.
Support(s) must be placed under all por
tions of the panel overhanging the table
top.
Use extra caution when cutting a work
piece that is twisted, knotted, warped or
does not have a straight edge to guide it
with a mitre gauge or along the fence. A
warped, knotted, or twisted workpiece is
unstable and causes misalignment of the
kerf with the saw blade, binding and kick
back.
Never cut more than one workpiece,
stacked vertically or horizontally. The saw
blade could pick up one or more pieces and
cause kickback.
When restarting the saw with the saw
blade in the workpiece, centre the saw
blade in the kerf so that the saw teeth are
not engaged in the material. If the saw
blade binds, it may lift up the workpiece
and cause kickback when the saw is restar
ted.
Keep saw blades clean, sharp, and with
sufficient set. Never use warped saw
blades or saw blades with cracked or bro
ken teeth. Sharp and properly set saw
blades minimise binding, stalling and kick
back.
4) Table saw operating procedure warnings
Turn off the table saw and disconnect the
power cord when removing the table in
sert, changing the saw blade or making
adjustments to the riving knife or saw
blade guard, and when the machine is left
unattended. Precautionary measures will
avoid accidents.
Never leave the table saw running unat
tended. Turn it off and don’t leave the tool
until it comes to a complete stop. An unat
tended running saw is an uncontrolled haz
ard.
Locate the table saw in a well-lit and level
area where you can maintain good footing
English
29
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TKS 80 EBS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TKS 80 EBS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info