Manual Festool PS CARVEX 420 EBQ (page 16 of 107) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

497992

Zoom out

Zoom in

1/107

C A R V E X

If the saw blade is stuck and cannot be

changed:

Operate the jigsaw at high speed

for 3 - 10 seconds. Actuate the saw blade ejec-

tion

[3-3]

again.

7.2 Using the chip guard

The chip guard

[3-1]

prevents chips flying

away and improves the efficiency of the chip

extraction system.

Using minimal pressure, push the chip

guard

[3-1]

downwards.

7.3 Inserting the splinterguard

The splinterguard prevents the edges of the

material from splintering during the cut, even

at the end where the saw blade exits the ma-

terial.

Switch off the machine and slide the splin-

terguard

[4-1]

into the guide

[4-2]

and

up to the saw blade,

Switch on the jigsaw,

On a level surface, slide in the splinter-

guard

(not using your hand!)

while the

machine is operating until it is flush with

the front edge of the saw base (speed set-

ting 5). This beds in the splinterguard.

When it is worn, push the splinterguard ap-

prox. 3 mm further to the rear and continue

using it.

To guarantee reliable operation of the splin-

terguard, it must seal tightly on both sides

of the saw blade. A new splinterguard

should therefore be fitted after every saw

blade change to guarantee splinter-free

cuts.

7.4 Changing saw table

Open the change lever

[1-9]

Removing the saw table downwards.

Assembly is performed in reverse sequence

to removal. Ensure that the saw table is

firmly seated in the guide.

Instead of the saw table, the angle table WT-

PS 400 or adaptation table ADT-PS 400 can be

installed at the support.

Never saw without the saw table, or one

of the other tables offered in the Festool

accessories program.

7.5 Dust extraction

The extraction adapter

[5-3]

allows jigsaws

to be connected to a dust extractor (hose di-

ameter 27 mm).

Insert the extraction adapter into the rear

opening of the saw table so that the hook

[5-2]

engages in the

[5-1]

recess.

To remove the extraction adapter, press the

hook

[5-2]

Due to the low power consumption of the

machine (low energy consumption), dust

extractors with an automatic switch-on

function will sometimes only start up when

the actual cut is made.

Set the dust extractor to continuous opera-

tion for special applications (e.g. low stroke

rate, soft wood).

7.6 Adjusting the pendulum stroke

In order to process different materials with an

optimum feed movement the pendulum jig-

saws have an adjustable pendulum stroke. Se-

lect the desired setting with the pendulum

stroke switch

[1-12]

setting 0 = pendulum stroke off

setting 3 = maximum pendulum stroke

7.7 Stroke speed control

The number of strokes can be adjusted step-

lessly with the adjusting wheel

[1-5]

between

1500

and

3800

rpm (

PSB 420 EBQ

1000 -

3800

rpm). This enables you to optimise the

cutting speed to suit the respective material.

WARNING

Dust hazard

Dust can be hazardous to health. Always

work with a dust extractor.

Always read applicable national regula-

tions before extracting hazardous dust.

Recommended settings of the pendu-

lum stroke

Hard and soft wood,chip board,

wood fibre board

1 - 3

Wood core plywood, plywood, plas-

tics

1 - 2

Ceramic 0

Aluminium, NF metals 0 - 2

Steel 0 - 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool PS CARVEX 420 EBQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool PS CARVEX 420 EBQ Manual

Product: