497992
17
Zoom out
Zoom in
Previous page
1/107
Next page
C A R V E X
17
GB
In position
A
, the automatic load detection is
activated: The stroke speed is reduced in
idling and is controlled to the highest value
when the blade enters the workpiece.
8 Working with the machine
When working on small or thin workpieces, al-
ways use a stable base, or the CMS module
(accessory).
When working, hold the electric power tool by
the handle and guide it along the desired cut-
ting line. For precise cuts and smooth running,
use two hands to guide the electric power tool.
Free saw guidance along a scribe mark
The triangular pointer on the splinterguard
[4-1]
indicates the cutting line of the saw
blade. This facilitates sawing along a scribe
mark.
8.1 Lighting
A continuous light or stroboscope is installed
for illuminating the cutting line:
up to approx. 2100 rpm: continuous light
from approx. 2100 rpm: stroboscope light
L
In overhead position (+/- 45°), the lighting
is switched off completely.
If required, you can adjust the lighting:
X
Plug in the electric power tool.
X
Press both buttons simultaneously
[1-2]
and hold for approx. 10 s until a beep
sounds.
X
Release both buttons
[1-2]
.
X
Press the left button (on the pendulum
stroke side) to select the stroke speed and
consequently the desired operating mode:
X
Press the right button to save the setting.
9 Service and maintenance
Customer service and repair
only through manufacturer or ser-
vice workshops: Please find the
nearest address at:
www.festool.com/Service
Use only original Festool spare
parts! Order No. at:
www.festool.com/Service
Damaged safety devices and components
must be repaired or replaced in a recognised
specialist workshop, unless otherwise indicat-
ed in the operating manual.
Recommended stroke speed (position
of the adjusting wheel)
Hard and soft wood, plywood board,
plywood, chip board
A
Hardboard 4 - A
Plastic 3 - A
Ceramic, aluminium, non-ferrous
metals
3 - 5
Steel 2 - 4
CAUTION
Material with high dust generation (e.g.
plasterboard)
Damage to machine through dust pene-
tration, risk of injury
X
Do not work overhead!
WARNING
The stroboscope light may make it diffi-
cult to determine the saw blade posi-
tion
Risk of injury
X
Ensure the work area is well illuminated.
Mode Indication
during config-
uration
Behaviour dur-
ing operation
1 Light flashes With strobo-
scope (standard)
2 Light on Permanent light
without strobo-
scope
3 Light off Light switched off
WARNING
Risk of injury, electric shock
X
Always disconnect the mains plug from the
socket before performing maintenance
work on the machine!
X
All maintenance and repair work which re-
quires the motor housing to be opened
must only be carried out by an authorised
service workshop.
EKAT
1
2
3
5
4
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PS CARVEX 420 EBQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PS CARVEX 420 EBQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info