Manual Festool IS330EB (page 26 of 192) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

573136

Zoom out

Zoom in

1/192

 Using the bevel indicator [4-3], adjust the cut-

ting angle to the required value (the bevel indi-

cator is divided into 1° increments).

 Re-tighten the hand screws [4-2].

7.3 Motor electronics

Starting current limitation

Smooth, electronically controlled starting ensures

that the machine starts without kickback. Due

to the machine’s limited starting current, a 16 A

circuit breaker is sufﬁ cient.

Idle speed reduction

The electronics reduce the machine’s RPM dur-

ing idle, which also decreases wear to the motor

and gears.

Constant electronics

Constant electronics maintain the RPM the same

at idle and under load, which ensures uniform

work movement and a high-quality cut.

Electronic overload protection

If the machine is extremely overloaded, electronic

protection guards the motor from damage. In this

case, the motor stops and resumes only after dis-

charge, and after the switch is engaged again.

Thermal overload protection

To prevent overheating under an extreme long-

term load, the safety electronics switch the motor

into cooling mode when the critical temperature

is reached. The machine cannot be loaded, and

it runs at reduced RPM. After cooling, the tool

is once again prepared for operation and can be

fully loaded in about 3 – 5 minutes. If the tool gets

hot while running, the heat protection reacts cor-

respondingly earlier.

RPM selection

Using the RPM regulator [1-14], it is possible to

preselect the RPM continuously:

Level 1: 2200 min

–1

Level 4: 3600 min

–1

Level 2: 2600 min

–1

Level 5: 4100 min

–1

Level 3: 3200 min

–1

Level 6: 4600 min

–1

8 Preparation for use

8.1 Mounting the chain

WARNING

Risk of accident if the machine is operated us-

ing unauthorised voltages or frequencies.

 The mains voltage and the frequency of the

power source must correspond with the

speciﬁ cations on the machine’s name plate.

 In North America, only Festool machines with

the voltage speciﬁ cations 120 V/60 Hz may

be used.

WARNING

When mounting the chain make sure it seats

correctly. The cutting teeth must be positioned

in the direction that conforms to the chain rota-

tion, i. e., the mark shown on the body of the saw.

When the IS 330 EB is delivered, the chain is not

mounted on the guide bar.

 Remove the chain sprocket cover [2-

1] by rotating the fastening wheels

[2-2] counter clockwise, as shown in Fig. [2].

 Put a new chain [2-3] on the guide bar [2-4]

and insert it into the machine. Maintain the

proper position of the cutting teeth, accord-

ing to the direction of rotation. The direction of

rotation is indicated by an arrow on the body

of the machine, and under the chain sprocket

cover there is a symbol showing how the chain

should be mounted.

 Place the guide elements of the chain onto

the chain sprocket [2-8] and turn using the

chain adjustment wheel [2-9] (when rotated

clockwise as seen from above, the pin moves

upwards and releases; when rotated counter

clockwise as seen from above, the pin moves

downward) so that the opening on the guide bar

[2-5] snaps into the tension bolt [2-6].

 Then put the chain sprocket cover [2-1] on the

clamping bolt [2-7] and tighten by rotating the

fastening wheel [2-2] clockwise.

 Before tightening it ﬁ rmly, tension the chain

correctly, as described in Section 11.1.

8.2 Filling the oil reservoir

When the IS 330 EB is delivered, the lubrication

oil reservoir is empty. Before using the machine,

you must ﬁ ll the tank with chain oil to prevent

damage to the oil feed pump. If the machine is

operated with an insufﬁ ciently ﬁ lled oil reservoir

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool IS330EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool IS330EB Manual

Product: