573136

Festool IS330EB Manual

25
Zoom out
Zoom in
Previous page
1/192
Next page
25
5.3 Residual risks
Even if the machine is used to specifi cation and
all relevant safety regulations are followed, the
following residual safety risks may nonetheless
occur due to the design of the machine and its
usage:
- Injury from the cutting teeth when replacing
the chain.
- Injury from touching the chain on its cutting
area.
- Catching clothes in the moving chain.
- Injury from fl ying scraps or parts of the ma-
chine.
- Danger that may be caused by the portable
cord.
- Kickback caused by the chain or the operating
the tip of the plate jamming.
- Concentration of sawdust jeopardising health
in poorly ventilated areas.
- Injury from touching electrically charged parts
when dismantling the machine or any part of it
while the machine is still plugged in.
- Hearing damage from prolonged work without
ear protectors.
5.4 Emission levels
Levels determined in accordance with EN 60 745
are typically:
Sound pressure level L
PA
= 92 dB (A)
Noise level L
WA
= 103 dB (A)
Uncertainty K = 3 dB
Acoustic output value measured according to es-
tablished guideline 2000/14/EC, appendix VI.
L
WA
= 103 dB (A)
L
WA d
= 105 dB (A)
Uncertainty K = 3 dB
Measurement was performed by notifi ed indi-
vidual No. ES-1014 EZU s. p. Pod Lisem 129, 171
02 Prague 71.
CAUTION
Operating noise
Damage to hearing
Use ear protection!
Vibration emission value a
h
(vector sum for three
directions) and uncertainty K measured in accord-
ance with EN 60 745:
a
h
= 3.4 m/s
2
Uncertainty K = 1.5 m/s
2
The specifi ed emissions values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary es-
timates regarding vibration and noise loads
during operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with oth-
er insertion tools or if not maintained adequately.
Take note of idling and downtimes of machine!
6 Transport and delivery
The IS 330 EB insulation saw has been tested and
is delivered in perfect condition. The oil reservoir
of the machine IS 330 EB is not fi lled. When the
machine is delivered, take it directly out of the
packaging and check for potential damage during
transport. Any damage caused during transport
must be reported to the carrier immediately.
6.1 Storage
The packed insulation saw can be stored in a
dry storage area without a heating, where the
temperature does not drop bellow −5 °C. Store
the unpacked saw only in a dry closed storage
where the temperature does not drop below +5
°C, and where sudden temperature changes are
prevented.
7 Adjustment
CAUTION
All adjustments and settings must be carried
out before the machine is switched on.
WARNING
Risk of accident, electric shock
Always pull the plug out of the socket before
performing any type of work on the machine.
7.1 Tilting the guide bar lengthwise
The guide bar, including the guard plate, can be tilt-
ed 10° backward. This adjustment is mainly used
when multiple layers are cut at the same time. It
prevents resistance to the tool and an uneven cut.
Release lever [3-1] upward (Fig. [3a]).
By pulling the handle, tilt the guide bar back-
wards and secure it again with the lever [3-1]
downward (Fig. [3b]).
7.2 Cutting angle adjustment
WARNING
For bevel cuts the maximum cutting depth is
limited.
Release the hand screws [4-2] on both sides.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool IS330EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool IS330EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info