778630
23
Zoom out
Zoom in
Previous page
1/142
Next page
ing cut, the motor is switched off immediately.
To put the power tool back into operation, it
must first be switched off and then on again.
Restart protection
The built-in restart protection prevents the
power tool from starting up again automatically
if the power is disconnected during continuous
use. To put the power tool back into operation,
it must first be switched off and then on again.
Overheating protection
In the event of overheating, the safety electron
ics system switches to cooling mode. The motor
continues to run and the constant speed is de
activated. Let the machine cool down for ap
proximately 10–20 seconds before using it
and/or fully loading it again.
6 Commissioning
The dust extraction attachment is preassem
bled and must not be removed or repositioned.
6.1 Holding the power tool correctly
Hold the power tool with both hands using the
insulated gripping surfaces [1-8]: One hand on
the motor housing behind the switch and the
other on the auxiliary handle [1-3].
6.2 Switch on/off
Switching on [2a]
Push the on/off switch [1-4] forwards.
Pressing the front part of the switch at the
same time locks the on/off switch.
On/off switch [1-4] is locked and the power tool
is switched on.
Only position the tool on the material once
it has reached operating speed.
Setting the speed
The speed can be adapted in six settings de
pending on the workpiece requirements.
Set the speed regulator [1-7] to the re
quired setting.
Switching off [2b]
Lift the power tool from the processed ma
terial.
Press the rear part of the on/off
switch [1-4].
Lock is released and the power tool is switched
off.
WARNING
Risk of injury from kickback, ejected parts
Before setting down the power tool, wait
until the rotating sanding tool has come to
a complete stop.
Set the power tool down flat on the dust ex
traction attachment.
7 Battery pack
Inserting the battery pack [3a]
Removing the battery pack [3b]
7.1 Capacity display
The capacity display [1-12] indicates the charge
of the battery pack for approx. 2 seconds after
the button [1-11] is pressed:
70‑100%
40‑70%
15‑40%
< 15% *
* Recommendation: Charge the battery pack
before any further use.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Settings
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
8.1 Fitting the auxiliary handle [1-3]
Always use the auxiliary handle to ensure
a safe working posture that prevents you
from tiring.
The special "VIBRASTOP" design of the auxiliary
handle helps to reduce vibrations.
Screw in the auxiliary handle [1-3] on the
side of the thread [1-2] according to the
working method.
English
23
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool DSC-AGC 18 FH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool DSC-AGC 18 FH in the language / languages: All languages as an attachment in your email.

The manual is 3.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info