778812
23
Zoom out
Zoom in
Previous page
1/126
Next page
23
9.2 Motor electronics
Starting current limitation
Electronically controlled continual running se-
cures device acceleration without back thrust.
Due to starting current limitation in the device,
16A protection is suffi cient.
WARNING
Devices without starting current limitation
need higher protection – at least 16A circuit
breaker.
Speed control
You can regulate the speed steplessly within the
speed range using the adjusting wheel [1-15] (see
Technical data). This enables you to optimise the
speed to suit the respective material. Please also
note the specifi cations on the tools.
Switching off during back thrust
During sudden drop of revolutions, for example
blocking in dividing cut, the current input in mo-
tor stops. For re-starting, the device must be fi rst
switched off and again switched on.
Protection against re-starting
Prevent uncontrolled starting of the device after
current supply cut off. For re-starting, the device
must be fi rst switched off and again switched on.
Constant speed
The preselected motor speed remains constant
through electronic control to ensure a uniform
cutting speed even when under load.
Protection from overloading dependant on tem-
perature
The safety electronics switches to cooling regime
when the critical temperature is reached. Motor
continues running at approximately 50 % revolu-
tions, constant electronics is deactivated.
After cooling to approximately 10 20 s, the device
is fully operational.
Heat protection for devices heated during opera-
tion, reacts adequately sooner.
9.3 Turning the gear box
For special cases, the gearbox can be turned in
steps of 90°. This achieves a better handling posi-
tion of the switch.
For such work, we recommend to use the Festool
service.
Remove four screws.
Carefully, turn the gearbox into required posi-
tion. Make sure the gearbox does not separate
from motor box by more than approximately
1mm.
Insert and fasten the four screws -fi gure [8].
9.4 Aperture cover
If you wish to see the cutting area, take off the
aperture cover [2-3]. Only handle this cover when
the disc is not running.
Be careful about spattering dust particles.
10 Service and maintenance
WARNING
Risk of accident, electric shock
Always pull the plug out of the socket before
performing any type of work on the machine.
All maintenance and repair work which re-
quires the motor housing to be opened, must
only be carried out by an authorised service
workshop.
- Wrapped electric tools can be stored in a dry
place without heating, with temperatures not
lower than –5°C. Unwrapped electric tools can
only be stored in dry places with temperatures
not lower than +5°C, without sudden changes
in the temperature.
-To ensure the airfl ow is suffi cient, cooling
openings of the motor must be always clean
and free.
-The machine is equipped with special self-
disconnecting brushes. When the brushes are
worn, the power supply is automatically discon-
nected, and the machine is stopped.
-If the suction fl ange height adjustment system
does not operate smoothly, the fl ange must be
removed and cleaned.
Customer service and repair. Only through
manufacturer or service workshops:
Please fi nd the nearest address at: www.
festool.com/service
EKAT
1
235
4
Use only original Festool spare parts! Or-
der No. at:
www.festool.com/service
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool DSC-AG 125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool DSC-AG 125 in the language / languages: All languages as an attachment in your email.

The manual is 7.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info