Manual Festool DSC-AG 125 (page 22 of 126) (All languages)

778812

Zoom out

Zoom in

1/126

cutting performance of the machine (periph-

eral speed of the grinding and cutting wheels).

Set the sliding stop for cut depth [2-5] on scale

[2-4] to a depth value of 10 mm.

Push the arresting button [1-1] and push the

cover in.

Release the arresting button [1-1] and let the

cover be arrested when it gets to the set depth.

Unlock with button [2-1] and fully open the disc

cover.

Clean the ﬂ ange [6-4] and clamping nut [6-2],

as well as the clamping faces of the cutting

disc [6-3].

Put the ﬂ ange [6-4] on the grinder’s spindle

with the shoulder facing outward.

Put on the disc [6-3]; take care to comply with

the prescribed direction of rotation (arrow on

the disc vs. arrow on the machine). The ﬂ ange

shoulder must exactly ﬁ t in the disc’s opening.

Screw on the clamping nut [6-2] with the shoul-

der facing outward (from the disc), press on the

spindle arrest and tighten with wrench [6-1].

Close the disc cover.

Before switching on, check free rotational

movement of the disc.

8.2 Guide system [ﬁ gure 7]

WARNING

Only use discs of thickness up to 3 mm!

Use the guide bar [7-1] for accurate cuts.

The side clearance of the disc guiding can be set

with the aid of the adjusting screws [1-9].

Guide bars

On the bottom face of the guide bar there are anti-

skid strips, which ensure safe contact and prevent

the workpiece from scratching.

The bar can also be secured with the aid of special

clamps FSZ 300 [7-2], pushed into the special

guide grooves. Safe guiding on uneven surfaces

is thus enabled.

WARNING

The guide bars are equipped with burr protec-

tor, which must be cut off before the ﬁ rst use.

Connector

Depending on the particular application and the

workpiece size, several guide bars can be con-

nected with the aid of a connector spring [7-3].

Fast connection of guide bars can be secured by

screws in the threaded openings.

9 Activation

WARNING

Risk of accident if the machine is operated us-

ing unauthorised voltages or frequencies.

The mains voltage and the frequency of the

power source must correspond with the spec-

iﬁ cations on the machine’s name plate.

In North America, only Festool machines with

the voltage speciﬁ cations 120 V/60 Hz may

be used.

Set the sliding stop for cut depth [2-5] on scale

[2-4] (top edge of the stop) to the requested depth

of the cut – loosen and tighten the stop screw [2-

6] as necessary.

The cut depth scale is valid for cutting without a

bar.

The scale is for orientation only. The actual depth

of the cut may be affected by, for example, manu-

facturing tolerances or the wear of the diamond

disc’s segment. If en exact depth is required, it

is necessary to measure the actual depth on a

test cut.

9.1 Switching on – off

Switching on

Slide the on/off switch [1-5] forwards.

Continuous operation: pressing the front part

of the switch at the same time locks the on/

off switch.

The electric power tool starts.

Only make contact with the material once the

machine has reached operating speed.

Switching off

Lift the electric power tool from the processed

material.

Release the on/off switch [1-5].

During continuous operation: press on the

rear part of the on/off switch [1-5].

WARNING

Risk of injury

Rebound, ejected parts

Before setting down the machine, wait until

the rotating tool has come to a complete stop.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool DSC-AG 125 in the language / languages: All languages as an attachment in your email.

The manual is 7.06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool DSC-AG 125 Manual

Product: