Manual Festool DOMINO XL DF 700 EQ (page 17 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

498004

Zoom out

Zoom in

1/116

DF 700 EQ

8 Working with the machine

Wood is a natural, non-homogenous material

and because of this, its dimensions will most

likely deviate slightly during processing,

even if the machine is set accurately. Ma-

chine handling also influence the degree of

working accuracy (e.g. fast-feed speed).

Furthermore, the dimensions of wooden

DOMINOs may vary (for example, due to hu-

midity), regardless of how they are stored.

All of these factors influence the dimensional

accuracy of manufactured dowel holes and

dowelling joints.

We recommend

routing and joining a

test workpiece before machining the actu-

al workpiece.

Please observe all mentioned safety in-

formations and the following rules

when working:

– Always secure the workpiece in such a

manner that it cannot move while being

processed.

– Always hold the machine with two hands

on the handles [1-3] when performing

work. This reduces the risk of injury and is

a prerequisite for precise work.

– Close the clamp lever for routing height

adjustment [1-14]and the clamp lever for

angle adjustment [1-12]to avoid uninten-

tional loosening during operation.

– Adapt the feed rate to the cutter diameter

and material. Work with a constant feed

rate

– Only lay the machine aside when the cutter

has come to a complete standstill.

– Always connect the machine to a dust ex-

tractor.

For work that generates dust, wear a

dust mask.

Procedure

Proceed as follows to create a DOMINO dow-

elling joint:

9 Service and maintenance

The machine is equipped with special carbon

brushes. If they are worn, the power is inter-

rupted automatically and the machine comes

to a standstill.

See chapter

1. Select a DOMINO dowel and insert

the suitable bit into the DOMINO

joining machine.

7.2

2. Set the routing depth. 7.3

3. Set the routing height. 7.4

4. Adjust the routing angle if neces-

sary.

7.5

5. Mark the areas on the workpieces

that belong together [8-1]so that

you will be able to join them cor-

rectly again once you have cut the

dowel holes.

Position the two workpieces to be

joined against one another and

mark the desired positions of the

DOMINO dowels with a pencil [8-

2].

Select the required stop pins. 7.7

7. Set the desired dowel hole width

(adequate fit or with 3 mm play).

7.6

8. Cutting the dowel holes [8]:

– The first dowel hole by attaching

the stop pin to the side edge of

the workpiece.

– The following dowel holes ac-

cording to the previously made

pencil markings and the scale of

the vision panel [8-3].

Our recommendation:

Please

check each dowel hole for chip-

pings and clear these if necessary.

Always work with a dust extractor

to improve the removal of chip-

pings.

Route the first hole for each work-

piece without play (dowel hole

width = DOMINO dowel width) and

the other dowel holes with the

large dowel hole width.

WARNING

Risk of injury, electric shock

Always disconnect the mains plug from the

socket before performing maintenance

work on the machine!

All maintenance and repair work which re-

quires the motor housing to be opened

must only be carried out by an authorised

service workshop.

See chapter

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool DOMINO XL DF 700 EQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool DOMINO XL DF 700 EQ Manual

Product: