796189
22
Zoom out
Zoom in
Previous page
1/152
Next page
5.2 Remote control CT-F I
[1-19] Connection button
[1-20] LED indicator
[1-21] MAN button (for manually switching
on)
[1-22] Attachment point for the fastening
straps
[1-23] Fastening strap
The specified illustrations appear at the begin
ning of the Operating Instructions.
* Accessories shown or described are not al
ways included in the scope of delivery.
6 Preparations
Insert the filter/disposal bag [2-1].
Connect the suction hose [3].
7 Battery pack
Before using the battery pack, check that the
battery interface is clean. Any contamination of
the battery interface may impair correct contact
and lead to the contacts being damaged.
A faulty contact may result in the machine over
heating or being damaged.
[4A] Remove the battery pack.
[4B]
klick
Insert the battery pack – until it
clicks into place.
The cordless mobile dust extractor can
only be operated with two battery packs.
For a listing of possible battery pack var
iants for operation of the device, see ta
ble [5]. For newer battery packs that are
not listed, follow the instructions from the
Festool Work App or contact the Festool
customer service team.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Commissioning
Standby mode
Press the on/off button [1-12].
The green LEDs on the status display [1-15] in
dicate standby mode.
Pressing the on/off button again will switch off
the cordless mobile dust extractor.
Starting/stopping the cordless mobile dust
extractor manually
The cordless mobile dust extractor is in standby
mode.
Directly on the cordless mobile dust extractor:
Press the MAN button [1-13] to start/stop.
Alternatively, use the connected remote control
CT-F I (see chapter 9.2):
Press the MAN button [1-21] on the remote
control to start/stop.
Starting/stopping the cordless mobile dust ex
tractor automatically
The cordless mobile dust extractor is in standby
mode.
To start/stop the cordless mobile dust ex
tractor automatically: Switch the connected
battery-powered power tool on/off (see
chapter 9.1).
9 Connecting a device
WARNING
Risk of injury from a cordless mobile dust
extractor starting up unsupervised
Before performing any work with the cord
less mobile dust extractor, check which re
mote control and which cordless power
tool are connected to the cordless mobile
dust extractor.
A battery-powered power tool must always
be connected to the cordless mobile dust
extractor via the suction hose. After finish
ing work, the connection to the cordless
mobile dust extractor must be disconnec
ted.
The remote control must only be attached
to the suction hose.
9.1 Connecting a battery-powered power
tool
In standby mode, press the connection but
ton [1-16].
The connection display [1-17] slowly flashes
blue. For a period of 60 seconds, the cordless
mobile dust extractor is ready for connection.
Switch on the power tool.
The cordless mobile dust extractor starts up.
The cordless mobile dust extractor is connec
ted until the on/off button [1-12] is pressed or a
battery pack is removed (from the cordless mo
bile dust extractor). The power tool must then
be connected again.
English
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CTLC MINI I at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CTLC MINI I in the language / languages: All languages as an attachment in your email.

The manual is 17.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info