724593
22
Zoom out
Zoom in
Previous page
1/44
Next page
52cc 2 Stroke Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: info.aldi@positecgroup.com
1300 889 028
MODEL: №. SBC52 • 02/2020 • 700710
(toll free)
20
Fitting the Spool and Line Assembly on the Line Trimmer
NOTE: If the unit has been used as a brushcutter rst, the brushcutter blade
will need to be removed before tting the spool and line assembly.
Refer to “Changing/Removing the Brushcutter Blade for instructions on how
to remove the blade.
NOTE: Always ensure the engine is turned o before undertaking this
assembly.
1. Lay the unit down so that the fuel tank bracket (39) is facing upwards and
the engine is resting on the ground. Lift the gearbox end of the lower
shaft (15) to gain access to the spindle (20).
IMPORTANT: Ensure the inner ange is mounted on the spindle of the line
trimmer. The outer ange (29), the protector (27), the 3T brushcutter blade
(28) and the blade nut (26) are NOT required when the line trimmer spool &
line assembly (35) is being tted.
Keep these components in a safe place. The 3T brushcutter blade (28)
should be placed back in the cardboard packaging/envelope.
2. Place the spool and line assembly (35) on the
spindle (20) and thread on to the spindle nger
tight in an anti clockwise direction all the way
down until the back of the spool makes contact
with the inner ange (30) (Fig W).
3. Insert the long end of the supplied 4mm allen
key (37) through the spindle lock entry hole (19)
and into the hole on the inner ange (30).
(This locks the spindle allowing the spool and
line assembly (35) to be secured). Further tighten
the spool and line assembly (35) ensuring the
assembly is tight on the spindle (20) and inner
ange (30) before removing the 4mm allen key
from the spindle hole to release the spindle
being locked (Fig. X).
4. To remove the spool and line assembly (35),
follow this procedure in reverse.
A.
A.
X.
W.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex SBC52 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex SBC52 in the language / languages: English as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info