724587
13
Zoom out
Zoom in
Previous page
1/20
Next page
AFTER SALES SUPPORT
(toll free)
e-mail: info.aldi@positecgroup.com1300 889 028
30W Wood Burning Kit
PSI30 • 05/2020 • 701256
05/2020
10
6) Hold the soldering tin (not supplied) against the hot tip until the metal
is liquied and ows onto the point to be soldered. Melt the soldering tin
(with soldering ux) (not supplied) between the soldering point and the
soldering tip. Add further soldering tin until the entire soldering point has
been wetted.
7) Allow the solder to solidify and avoid any vibrations.
8) Clean the soldering tip with a clean, damp sponge. After cleaning, the
soldering tip must be tinned: Tin the hot soldering tip by melting the
soldering tin.
9) Turn o the mains power switch, and disconnect the plug from the
mains socket after nishing your work and allow the device to cool down
for at least 30 minutes.
NOTE: The soldering and branding iron has a nominal power rating of 30
Watts and is thus ideal for soldering electronics. It is particularly suitable for
hard to reach areas and ne soldering work due to its design.
The best results are achieved with electric solder with a diameter of 1.0 or
1.5 mm, 60% Sn, 40% Pb.
We recommend using a contact paste as a soldering ux (not soldering ux
greases or soldering ux liquid). The soldering ux is either contained in
the solder or is applied separately.
5. Cutting tip (Fig F)
1) Screw the cutting tip onto the branding rod
(2) as described in "Fitting the soldering tip and
the branding accessories".
2) Place the branding rod onto the stand (9) so
that the Y-shaped mount on the stand supports
the branding and soldering iron between the
sleeve and the handle.
3) Connect the power plug into a mains power socket, and then turn the
mains power switch on. Ensure that the power supply is suitable. The
device is now heating up.
4) Wait for approx.10 minutes until the branding accessory has heated up
fully.
5) You can use the cutting tip to cut the plastic or soft materials.
6) Hold the device on the handle like a pen while working.
F.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex PS130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex PS130 in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info