779780

Ferrex FPCS46 E1 Manual

38
Zoom out
Zoom in
Previous page
1/50
Next page
Kapitelüberschrift
42
Fuel Filter
m NOTICE
Never use the saw without a fuel filter. After 100 hours in operation the fuel filter
should be cleaned or, in case of damage, replaced. Be sure to empty the fuel tank
before changing the filter.
1. Ensure the stop switch (Fig. 8/pos. 19) is set to ‘0’ stop.
2. Remove the fuel tank cap (Fig. 7/pos. 8).
3. Bend a piece of soft wire.
4. Reach into the fuel tank opening and hook the fuel line. Carefully pull the fuel
line toward the opening until you can reach it with your fingers.
m NOTICE
Do not pull hose completely out of tank.
5. Lift the filter out of tank.
6. Pull the filter off the fuel pipe with a twist and clean it. (If the filter is damaged,
dispose of it and replace it with a new filter).
7. Insert the end of the cleaned /new filter onto the fuel pipe. Place one end of the
filter into the tank opening. Make sure that the filter is seated in the lower corner
of the tank. If necessary, use a long screwdriver to move the filter to its correct
position, taking care not to damage it in the process.
8. Fill tank with fresh fuel / oil mixture. See the chapter: Set up.
Securely refit the fuel tank cap (Fig. 7/pos. 8).
Spark plug (Fig. 26)
m NOTICE
To ensure that the saw’s engine retains its power, the spark plug must be clean and
have the correct electrode gap (0.6-0.7 mm). The spark plug must be cleaned or
replaced after every 20 hours of service. Replacement spark plugs are available from
special dealers.
1. Ensure the stop switch (Fig. 8/pos. 19) is set to ‘0’ stop.
2. Remove the air filter cover (Fig. 23/pos. 5) and the air filter (Fig. 25/pos. B).
3. Disconnect the spark plug boot (Fig. 27/pos. C) from the spark plug (Fig. 27/pos.
D) by pulling and twisting it simultaneously.
4. Remove the spark plug using the supplied spark plug wrench (Fig. 1/pos. 23). DO
Maintenance and servicing
… 38 …


Need help? Post your question in this forum.

Forumrules
1

Forum

ferrex-fpcs46-e1

Reset search

  • How do I download the manual without some scumbag company telling me I have to download their version of PDF????? Submitted on 28-3-2024 at 02:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex FPCS46 E1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FPCS46 E1 in the language / languages: English as an attachment in your email.

The manual is 3.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info