734927
21
Zoom out
Zoom in
Previous page
1/34
Next page
Preparation
19
Pay attention to the direction in which the grinding/cutting
disc rotates.
Always use suitable protective gloves when handling the
grinding/cutting disc.
Removing the fitted grinding/cutting disc
1. Switch the grinder off and remove the battery from the battery holder
5
.
2. Attach the spanner
8
to the clamping flange
9
from below so that the
spanner fits into the clamping flange’s holes (see Fig.C).
3. Hold the spindle lock
1
down and use the spanner to loosen the clamping
flange’s screw connection by turning it anti-clockwise.
4. Completely unscrew the clamping flange from the spindle.
5. Remove the fitted grinding/cutting disc
14
from the spindle.
Fitting the grinding/cutting disc
1. Ensure that the grinder is turned off and that the battery is not in the battery
holder.
2. If necessary, insert the support flange
10
or align it correctly if the support flange
has been previously removed or incorrectly positioned (see Fig.C).
To do this, guide the support flange over the spindle 
11
as far as it will go and
align it with the spindle so that the side edges on the top of the flange fit into the
corresponding notches of the spindle.
3. Check that the support flange is placed properly on the spindle:
The support flange must be locked securely in place on the spindle.
The spindle should also turn when the support flange is turned.
4. Put the desired grinding/cutting disc
14
on the spindle.
Please note that the direction of the grinding/cutting disc depends on what type
of disc is used.
Therefore, please pay attention to the grinding/cutting disc’s direction shown in
Fig. D in this user manual as well as to the information from the grinding/cutting
disc manufacturer.
5. Place the clamping flange
9
on the spindle in the correct alignment. Please note
that the direction of the clamping flange depends on what type of disc is used.
Please therefore pay attention to the clamping flange’s direction shown in Fig. D
in this user manual.
6. Screw the clamping flange onto the spindle in a clockwise direction.
7. Attach the spanner
8
to the clamping flange from below so that the spanner fits
into the clamping flange’s holes (see Fig.C).
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex FAW 40-I at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FAW 40-I in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferrex FAW 40-I

Ferrex FAW 40-I User Manual - German - 36 pages

Ferrex FAW 40-I User Manual - French, Italian - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info