724581
10
Zoom out
Zoom in
Previous page
1/27
Next page
7
Safety instructions for all operations
Safety Warnings common for grinding, sanding, wire brushing, polishing,
carving or abrasive cutting-o operations:
a) This power tool is intended to function as a grinder, sander, wire brush,
polisher, carving or cut-o tool. Read all safety warnings, instructions,
illustrations and specications provided with this power tool.
Failure to
follow all instructions listed below may result in electric shock, re and/or
serious injury.
b) Operations such as polishing is not recommended to be performed
with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specically designed and
recommended by the tool manufacturer.
Just because the accessory can
be attached to your power tool, it does not assure safe operation.
d) The rated speed of the grinding accessories must be at least equal to
the maximum speed marked on the power tool.
Grinding accessories
running faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your accessory must
be within the capacity rating of your power tool.
Incorrectly sized
accessories cannot be adequately controlled.
f) The arbour size of wheels, sanding drums or any other accessory must
properly t the spindle or collet of the power tool.
Accessories that do
not match the mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Mandrel mounted wheels, sanding drums, cutters or other accessories
must be fully inserted into the collet or chuck.
If the mandrel is
insuciently held and/or the overhang of the wheel is too long, the
mounted wheel may become loose and be ejected at high velocity.
h) Do not use a damaged accessory. Before each use inspect the accessory
such as abrasive wheels for chips and cracks, sanding drum for cracks,
tear or excess wear, wire brush for loose or cracked wires. If power tool
or accessory is dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an accessory, position
yourself and bystanders away from the plane of the rotating accessory
and run the power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during this test time.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex DC-180E-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex DC-180E-1 in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info