Manual Ferm WLM1001-FWL-1000 (page 6 of 46) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

464648

Zoom out

Zoom in

1/46

Ferm 87

5. СЕРВИС И ОБСЛУЖИВАНИЕ

При выполнении работ по техническому обслуживанию двигател я

убедитесь, что машина не находитс я под напр я жением.

Машины фирмы Ferm созданы дл я работы в течении продолжительного промежутка

времени при минимальном техническом обслуживании.

Продолжительная удовлетворительна я работа зависит от соответствующего ухода за

машиной и регул я рной очистки.

Неисправности

На случай, если станок перестанет правильно работать, далее приводится несколько

причин и соответствующих решений:

Ремонт и обслуживание должен производить только квалифицированный

специалист или обслуживающая фирма.

Очистка

• Поддерживайте ваш станок в чистоте. Деревянную стружку и опилки удаляйте с

помощью щетки.

• Регулярно проверяйте клиновидный ремень на предмет трещин. При

необходимости замените его.

• Обеспечивайте чистоту вентиляционных пазов мотора. Удаляйте деревянную

стружку и опилки для предотвращения перегрева мотора.

• Затачивайте полукруглые долота и резцы для обеспечения легкости работы.

Смазка

Машина не нуждаетс я в дополнительной смазке.

• Заготовка вращается с биением или

не вращается вовсе при работающем

моторе.

• Резец выбивает из ваших рук.

• Проверить клиновидный ремень на

предмет трещин и убедиться, что его

натяжение в норме.

• Проверить достаточную заточку

резца.

• Выбрать для работы с данной

заготовкой более низкую скорость

посредством перемещения ремня.

• Проверить высоту упорных центров.

LIT

RUS

Ferm

• Before attatching a workpiece to the faceplate always ‘rough it out’ to as true round as

possible. This will minimise vibration while turning. Always fasten the workpiece securely

to the faceplate. Failure to perform these setup operations could cause the workpiece to

be thrown from the lathe.

• Avoid awkward hand positions where a slip could cause a hand to move into the

workpiece.

• Remove all knots before installing workpiece between centres or on the faceplate.

• Never leave the lathe work area, before the lathe has come to a complete stop.

• Do not lay your turning tools on the bench so that you must reach over the revolving

workpiece to select them.

• Keep firm hold and control of the cutting tools at all times. Special caution must be

excercised when knots or voids are exposed to the turning tool.

• Think safety, ware safety goggles.

• Complete hand sanding of between centres or faceplate mounted workpieces before

removing from the lathe. Do not exceed the speed used for the last cutting operation

performed on the workpiece, in accordance with the speed chart.

• Never atempt to remount a faceplate turning to the faceplate for any reason. Never

attempt to remount a between-centres turning if the original centres in the turning have

been altered or removed. Be positive the lathe is set at the lowest speed if remounting a

between-centres turning with non-altered original centres.

• Use extra caution in mounting a between-centres or spindle turning to the faceplate, or a

faceplate turning to between centres, for subsequent operation. Be positive the lathe is

set at lowest speed for turning on.

• Never mount a workpiece that contains any splits, cracks or knots to a faceplate or

between-centres.

Immediately switch off the machine when

• Interruption of the mains plug, mains lead or mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation

Electrical safety

When using electric machines always observe the safety regulations applicable in your country

to reduce the risk of fire, electric shock and personal injury. Read the following safety

instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating plate.

Replacing cables or plugs

Immediately throw away old cables or plugs when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the power input of the machine.

The minimum conductor size is 1.5 mm

. When using a cable reel always unwind the reel

completely.

LIT

RUS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm WLM1001-FWL-1000 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 3,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm WLM1001-FWL-1000 Manual

Product: