Manual Ferm TSM1033 (page 11 of 112) (English, Dutch, French, Italian, Swedish, Spanish, Finnish)

634180

Zoom out

Zoom in

1/112

Assembly of the saw blade

Fig. K

First remove the plug from the mains

before the saw blade is assembled or

replaced.

The arrow marked on the saw blade,

which indicates the direction of rotation.

Must point in the same direction as the

arrow marked on the machine, the saw

blade teeth must point downwards on

the front of the saw.

• Remove the inlay from the bench. Use a

screwdriver for this purpose.

• Turn the saw axle completely upwards (Fig.A, 5).

Remove the nut and the outside flange from the

saw axle (Fig. K, direction A).

• Now slide the saw blade over the saw axle and

now put the outside flange and the nut back.

Tighten the nut by hand.

• Now use the 2 keys: one for the flange and one

for the nut and now clamp it (Fig. K, direction B).

•

Now put the inlay back in the bench and fasten it.

Use of the mitring set-up

Fig. A

By turning the handle (4) at the front of the machine

you can adjust the saw blade to a maximum of 45°.

4. OPERATION

Switching On/Off

Fig. A (7)

• Press the switch into position ‘1’ to put your

machine into operation.

• To switch off the machine the same switch

needs to be pressed to position ‘0’.

• Always keep the mains cable away from

moving parts.

Using the height handle

Fig. A

• Turn height handle (5) clockwise to raise the

sawblade

• Turn height handle counterclockwise to lower

the sawblade

• Turn the saw blade approximately 2 mm higher

than the total thickness of the wood to be sawn.

Using mitre handle

Fig. A

• Release mitre handle (4) by turning the outer

part counter clockwise

• Use mitre handle to set the right mitre angle for

your cut by turning the inner part

• mitre handle by turning the outer part

clockwise.

Working instructions

There are two types of sawing methods:

• Lengthwise sawing

Sawing the workpiece in the length of the

wood grain.

• Cross-cutting or cutting off

Sawing off the workpiece crosswise.

If it concerns a panel, we do not usually

distinguish between the wood grain, but we name

the method where we saw off a part of the width

of the panel (lengthwise sawing) and when we cut

off the length (cross-cutting or cutting-off).

For both sawing methods one of the

fences must be used. Therefor never saw

without a fence!

Attention! Before you start sawing, first check the

following:

1. Is the saw blade secured?

2. Are all the locking handles secured?

3. Is the fence parallel to the saw blade?

4. Is the protective cap working properly?

5. Are you wearing safety goggles?

6. Is the saw blade not rubbing against anything?

It is absolutely necessary to take these

points into consideration before you start

work!

Lengthwise sawing

• Secure the fence to the correct measuring

position and remove the cut-off guide from the

bench carriage. (Fig. J)

• Turn the saw blade approximately 2 mm higher

than the total thickness of the wood to be

sawn.

• Press the wood lightly towards the bench and

let it glide against the cut-off fence.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1033 in the language / languages: English, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 10,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm TSM1033

Ferm TSM1033 User Manual - English, German, Dutch, French, Swedish, Spanish, Finnish - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1033 Manual

Product: