634180
9
Zoom out
Zoom in
Previous page
1/112
Next page
9
EN
38. Do not use saw blades which are damaged or
deformed.
39. Replace table insert when worn.
40. Only use saw blades specified by the
manufacturer that are intended for working
with wood or similar materials according to
EN847-1.
41. Take care that the selection of the saw blade
depends on the material to be cut.
42. Connect tabelsaws to a dust-collecting device
when sawing.
43. Use and correct adjustment of the riving knife
44. Use and correct adjustment of the upper saw
blade quard.
45. Take care when slotting.
Make sure, when changing the saw blade, the
blade width is not smaller and the main blade
thickness of the saw blade is not greater than the
thickness of the riving knife.
Wear personal protective equipment, these could
include:
Hearing protection to reduce the risk of
hearing loss
Eye protection
Inhale respiratory protection to reduce the risk
of harmful dust
Gloves when handling the blades and rough
materials (recommendation, saw blades, are
whenever practicable, carried in a container)
Warning! Do not use HSS blades.
Insert the push stick in its holder when not in
use.
Use a push stick or a push block to guide the
workpiece.
Warning! Do not use the saw for rebating
or grooving.
Only use saw blades, whose maximum speed
is at least the speed indicated on the saw and
is suitable for the material to be cut.
During the transport, the upper part of the saw
blade has to be covered, by the guard.
Switch off the machine immediately when you
discover:
A defective mains plug or mains lead.
A defective switch.
Overheating of the machine.
Smoke or odeur caused by scorched
insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
As a supply for this machine always use an
unloaded line and/or an extension cable with
conductors of at least 1,5 mm
2
and protected
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
This machine can be switched to the single-
phase network (230-240 V/50 Hz). If you are
in doubt about the earth of the electricity
provisions, consult an electrician first.
Power supply
The motor is fitted with an overload switch (8).
If the table saw overloads, the overload switch
switches the equipment off automatically to
protect the table saw from overheating. If the
overload switch triggers, switch off the table
saw using the ON/OFF switch (7) and wait
until the table saw cools down. Then press the
overload switch (8) and restart the table saw.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1033 in the language / languages: English, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 10,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm TSM1033

Ferm TSM1033 User Manual - English, German, Dutch, French, Swedish, Spanish, Finnish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info