634180
12
Zoom out
Zoom in
Previous page
1/112
Next page
12
EN
Remain at least 3 cm. from the front of
the saw blade before you switch on the
motor. The side of the wood which is
against the fence must be completely
straight. Keep your hands at least 10 cm
away from the saw track to be followed.
Switch on the motor and wait until the saw
blade has reached the maximum number of
revolutions before you start sawing.
While you press the wood against the bench
and the fence, you can carefully push the
wood through the saw blade without forcing it.
Never pull the workpiece backwards. If
necessary, switch off the motor first without
altering the position of the workpiece.
Lengthwise sawing with a (vertical) mitre
This method is practically the same, except that
the saw blade is placed at the angle required.
With this type of method the fence may
only be along the righthand side of the
sawblade.
Lengthwise sawing of narrow workpieces
Assume that this process is extremely
dangerous.
Take all the necessary safety measures and
continually push the workpiece through (until
behind the saw blade) using a push stick instead
of by hand.
Crosswise sawing
Remove the fence and apply the cross-cut
fence in the righthand carriage.
Adjust the height of the saw blade (see
lengthwise sawing).
Press the workpiece against the cross-cut
fence and keep at least 2,5 cm distance from
the front of the saw blade.
Switch on the motor and wait until the maxi-
mum number of revolutions has been reached.
Press the workpiece against the fence and
the bench. Carefully push the wood through
the saw blade. Continue until behind the saw
blade. Then switch off the motor and keep
this position until the saw blade has stopped
completely before you remove the wood.
Never pull the wood back. If necessary, switch
the motor off and keep the position until the
saw blade has stopped completely.
Crosswise sawing with a vertical mitre
This method is practically the same, except that
the saw blade is placed in the angle required.
Only place the cross-cut fence on the
righthand side of the saw blade. Never
saw too small pieces of wood. Never use
your hands to carry out difficult operations.
Crosswise sawing with a horizontal mitre
With this method the cross-cut fence must
be secured at the angle required. Keep the
workpiece pressed firmly against the cross-cut
fence and the bench before you start cutting off.
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
These machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Transporting the bench saw
Before transporting the bench saw, the following
steps must be carried out:
Pull the mains plug
Turn the hand-wheel 5 (Fig. A) in anticlockwise
direction, lower the blade as much as possible
Remove all accessories that cannot be
mounted firmly to the power tool
If possible, place unused saw blades in an
enclosed container for transport
Slide the saw-table extension 9 completely
inward and turn the knob (Fig F-3) to lock it
Wind the mains cable and bind it
For lifting or transport, carry the main table 2
(Fig.A)
The bench saw should always be carried by
two persons in order to avoid back injuries.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1033 in the language / languages: English, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 10,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm TSM1033

Ferm TSM1033 User Manual - English, German, Dutch, French, Swedish, Spanish, Finnish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info