510127

Ferm TSM1030 Manual

8
Zoom out
Zoom in
Previous page
1/52
Next page
8
EN
machine before you attend to the fault.
35. Avoid workpieces hitting back in your direction
by taking the following measures:
• Alwaysusesharpsawblades.
• Donotsawtoosmallworkpieces.
• Neverreleasetheworkpiecebeforeithas
been completely pushed through the saw.
• Alwaysadjusttheguideparalleltothesaw
blade.
• Neverremovethesawprotection.
36. Before you continue sawing, ensure that you
are standing rmly and that your hands are in
the required position.
37. Never use thinners to clean the machine. Only
use a damp cloth for cleaning.
38. Do not use saw blades which are damaged or
deformed.
39. Replace table insert when worn.
40. Use only saw blades recommended by the
manufacturer.
41. Take care that the selection of the saw blade
depends on the material to be cut.
42. Connect circular saws to a dust-collecting
device when sawing.
43. Use and correct adjustment of the riving knife
44. Use and correct adjustment of the upper saw
blade quard.
45. Take care when slotting.
Before use, remove the transport protection:
• Disassemble the bottom plate by loosening the
4 screws.
• Remove the transport protection below motor.
• The handles for height and mitre setting of the
saw blade are located in the transport
protection inside the machine.
• Reassemble the bottom plate.
Switch off the machine immediately when you
discover:
• A defective mains plug or mains lead.
• A defective switch.
• Overheating of the machine.
• Smoke or odeur caused by scorched
insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of re, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Alwayscheckthatthepowersupply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
• As a supply for this machine always use an
unloaded line and/or an extension cable with
conductors of at least 1,5 mm
2
and protected
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
• Only connect your machine and/or extension
cable to an earthed electricity mains.
• This machine can be switched to the single-
phase network (230 V/50 Hz). If you are in
doubt about the earth of the electricity
provisions, consult an electrician rst.
3. ASSEMBLY INSTRUCTIONS
Installation of the machine on a workbench or
on the subframe
This machine is a stationary machine and for
safety reasons must always be rmly installed
and not used for mobile applications.
You can install the machine in two ways:
a. As a stationary machine on a workbench. In
this case the machine must be secured to the
workbench with 4 bolts.
b. As a stationary machine on the subframe. In
this case the machine must be secured to the
subframe with 4 bolts and the subframe
anchored to the oor or to a oor plate with
dimensions of at least 1 square metre
Assembly of the bench saw on the workbench
Fig. B & C
Before adjusting the saw, make sure the
plug is removed from the socket.
Fig. B shows the distance of the holes to be
drilled in the workbench on which to fasten the
machine. Drill holes of 8 mm.
Only use the machine after it has been
assembled completely and it has been
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1030 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info