Manual Ferm TSM1030 (page 10 of 52) (English, German, Dutch, French, Spanish)

510127

Zoom out

Zoom in

1/52

you can adjust the saw blade to a maximum of

45° (4).

4. OPERATION

Working instructions

There are two types of sawing methods:

• Lengthwise sawing

• Sawingtheworkpieceinthelengthof

the wood grain.

• Cross-cutting or cutting off

• Sawingofftheworkpiececrosswise.

If it concerns a panel, we do not usually distinguish

between the wood grain, but we name the method

where we saw off a part of the width of the panel

(lengthwise sawing) and when we cut off the length

(cross-cutting or cutting-off).

For both sawing methods one of the

fences must be used. Therefor never

saw without a fence!

Attention! Before you start sawing, rst check the

following:

1. Is the saw blade secured?

2. Are all the locking handles secured?

3. Is the fence parallel to the saw blade?

4. Is the protective cap working properly?

5. Are you wearing safety goggles?

6. Is the saw blade not rubbing against anything?

It is absolutely necessary to take these

points into consideration before you start

work!

Lengthwise sawing

• Secure the fence to the correct measuring

position and remove the cut-off guide from the

bench carriage.

• Turn the saw blade approximately 2 mm

higher than the total thickness of the wood to

be sawn.

• Press the wood lightly towards the bench and

let it glide against the cut-off fence.

Remain at least 3 cm. from the front of

the saw blade before you switch on the

engine. The side of the wood which is

against the fence must be completely

straight. Keep your hands at least 10 cm

away from the saw track to be followed.

• Switch on the engine and wait until the saw

blade has reached the maximum number of

revolutions before you start sawing.

• While you press the wood against the bench

and the fence, you can carefully push the

wood through the saw blade without forcing it.

• Never pull the workpiece backwards. If

necessary, switch off the engine rst without

altering the position of the workpiece.

Lengthwise sawing with a (vertical) mitre

This method is practically the same, except that the

saw blade is placed at the angle required.

With this type of method the fence may

only be along the righthand side of the

sawblade.

Lengthwise sawing of narrow workpieces

Assumethatthisprocessisextremely

dangerous.

Take all the necessary safety measures and

continually push the workpiece through (until behind

the saw blade) using a synthetic aid instead of by

hand.

Crosswise sawing

• Remove the fence and apply the cross-cut

fence in the righthand carriage.

• Adjust the height of the saw blade (see

lengthwise sawing).

• Press the workpiece against the cross-cut

fence and keep at least 2,5 cm distance from

the front of the saw blade.

• Switch on the engine and wait until the

maximum number of revolutions has been

reached.

• Press the workpiece against the fence and the

bench. Carefully push the wood through the

saw blade. Continue until behind the saw

blade. Then switch off the engine and keep

this position until the saw blade has stopped

completely before you remove the wood.

• Never pull the wood back. If necessary, switch

the engine off and keep the position until the

saw blade has stopped completely.

Crosswise sawing with a vertical mitre

This method is practically the same, except that

the saw blade is placed in the angle required.

Only place the cross-cut fence on the

righthandsideofthesawblade.Never

sawtoosmallpiecesofwood.Never

useyourhandstocarryoutdifcult

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1030 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1030 Manual

Product: