Manual Ferm TSM1029 - FZB-250-1500 (page 8 of 60) (English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish)

634179

Zoom out

Zoom in

1/60

Ferm8

• Fig.Cshowstheparttobesawnout(310

x310mm),sothatthesawdustcanfall

throughitandpilingupisprevented!

 Onlyifyoudonotuseanextraction

system!

• Fastenthemachinewithbolts.

Whenusingthebase,thesamemustbexed

tothegroundusingfourboltsThesawinturn

mustbexedtothebasewithfourbolts.Check

theseboltsfortightnessbeforeswitchingonthe

machine.

Assembly and attachment of the rip fence

Fig. D1 + D2

• Attachthealuminiumfence(A)tothe

positioningblock(B).

• Nowyoucanattachthecompleteripfence

tothebenchtop.

• Slidetheripfenceviaoneendofthe

positioningrail(C)overthebenchtop.

• Adjustthepositionofthealuminiumfence

prole(A)suchthattheendcorresponds

totherearedgeofthesaw.

Assembly of the riving knife and the

protective cap

Fig. E1 - E3

• Turnthesawbladecompletelyupwards.

• Removethebenchinlay.

• Assembletherivingknifeontheset-up

forthispurposeanduseherebytheAllen

screwsandthellingrings.Ensurethatthe

rivingknifefallsproperlyintotheopening

(=groove).

• Nowputtheinlaybackinthebenchand

fastenit.

• Nowassemblytheprotectivecapontothe

rivingknifeanduseherebytheprolednut

andself-lockingnut.

Now lay a lath against the saw blade

and the riving knife and check whether

it falls properly into the extension of

the saw blade. If this is not the case:

Loosen the fastening bolts and place

or remove the lling rings.

• Abovethesawtabletheradialdistance

betweentherivingknifeandthetoothed

rimofthesawbladeshallnotatanypoint

exceed5mmatthedepthofcutset.

• Thetipoftherivingknifeshallnotbelower

than5mmfromthetoothpeak,asshown.

Assembly of the saw blade

First remove the plug from the mains

before the saw blade is assembled or

replaced.

• Removetheinlayfromthebench.Usea

screwdriverforthispurpose.

• Turnthesawaxlecompletelyupwards.

Removethenutandtheoutsideange

fromthesawaxle.

• Nowslidethesawbladeoverthesawaxle

andnowputtheoutsideangeandthenut

back.Tightenthenutbyhand.

• Nowusethe2keys:onefortheangeand

oneforthenutandnowclampit.

• Nowputtheinlaybackinthebenchand

fastenit.

Mounting the push stick holders

Fig. F2 - F4

Mountbothpushstickholdersonthesideofthe

machineusingtheboltsandringssupplied.

Use of the mitring set-up

Fig. A

Byturningthehandleatthesideofthemachine

youcanadjustthesawbladetoamaximumof

45°(4).

4. OPERATION

Working instructions

Therearetwotypesofsawingmethods:

• Lengthwisesawing

Sawing the workpiece in the length of

the wood grain.

• Cross-cuttingorcuttingoff

Sawing off the workpiece crosswise.

Ifitconcernsapanel,wedonotusually

distinguishbetweenthewoodgrain,butwe

namethemethodwherewesawoffapartof

thewidthofthepanel(lengthwisesawing)and

whenwecutoffthelength(cross-cuttingor

cutting-off).

For both sawing methods one of the

fences must be used. Therefor never

saw without a fence!

Attention!Beforeyoustartsawing,rstcheck

thefollowing:

1. Isthesawbladesecured?

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1029 - FZB-250-1500 in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1029 - FZB-250-1500 Manual

Product: