634179

Ferm TSM1029 - FZB-250-1500 Manual

9
Zoom out
Zoom in
Previous page
1/60
Next page
Ferm 9
GB
2. Areallthelockinghandlessecured?
3. Isthefenceparalleltothesawblade?
4. Istheprotectivecapworkingproperly?
5. Areyouwearingsafetygoggles?
6. Isthesawbladenotrubbingagainst
anything?
It is absolutely necessary to take these
points into consideration before you
start work!
Lengthwise sawing
• Securethefencetothecorrectmeasuring
positionandremovethecut-offguidefrom
thebenchcarriage.
• Turnthesawbladeapproximately2mm
higherthanthetotalthicknessofthewood
tobesawn.
• Pressthewoodlightlytowardsthebench
andletitglideagainstthecut-offfence.
Remain at least 3 cm. from the front of
the saw blade before you switch on
the engine. The side of the wood
which is against the fence must be
completely straight. Keep your hands
at least 10 cm away from the saw
track to be followed.
• Switchontheengineandwaituntilthesaw
bladehasreachedthemaximumnumber
ofrevolutionsbeforeyoustartsawing.
• Whileyoupressthewoodagainstthe
benchandthefence,youcancarefully
pushthewoodthroughthesawblade
withoutforcingit.
• Neverpulltheworkpiecebackwards.
Ifnecessary,switchofftheengine
rstwithoutalteringthepositionofthe
workpiece.
Lengthwise sawing with a(vertical) mitre
Thismethodispracticallythesame,exceptthat
thesawbladeisplacedattheanglerequired.
With this type of method the fence
may only be along the righthand side
of the sawblade.
Lengthwise sawing of narrow workpieces
Assume that this process is extremely
dangerous.
Takeallthenecessarysafetymeasuresand
continuallypushtheworkpiecethrough(until
behindthesawblade)usingasyntheticaid
insteadofbyhand.
Crosswise sawing
• Removethefenceandapplythecross-cut
fenceintherighthandcarriage.
• Adjusttheheightofthesawblade(see
lengthwisesawing).
• Presstheworkpieceagainstthecross-cut
fenceandkeepatleast2,5cmdistance
fromthefrontofthesawblade.
• Switchontheengineandwaituntilthe
maximumnumberofrevolutionshasbeen
reached.
• Presstheworkpieceagainstthefence
andthebench.Carefullypushthewood
throughthesawblade.Continueuntil
behindthesawblade.Thenswitchoffthe
engineandkeepthispositionuntilthesaw
bladehasstoppedcompletelybeforeyou
removethewood.
• Neverpullthewoodback.Ifnecessary,
switchtheengineoffandkeepthe
positionuntilthesawbladehasstopped
completely.
Crosswise sawing with a vertical mitre
Thismethodispracticallythesame,exceptthat
thesawbladeisplacedintheanglerequired.
Only place the cross-cut fence on the
righthand side of the saw blade. Never
saw too small pieces of wood. Never
use your hands to carry out difcult
operations.
Crosswise sawing with a horizontal mitre
Withthismethodthecross-cutfencemust
besecuredattheanglerequired.Keepthe
workpiecepressedrmlyagainstthecross-cut
fenceandthebenchbeforeyoustartcuttingoff.
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work
on the motor.
Themachineshavebeendesignedtooperate
overalongperiodoftimewithaminimumof
maintenance.Continuoussatisfactoryoperation
dependsuponpropermachinecareandregular
cleaning.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1029 - FZB-250-1500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1029 - FZB-250-1500 in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info