Manual Ferm TSM1011 - FZT-250EN (page 11 of 38) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

634097

Zoom out

Zoom in

1/38

Ferm 11

1. The engine does not start

• The plug is not in the mains.

• The cable has been interrupted.

2. The workpieces is jamming against the

riving knife during processing

• The saw blade must be aligned (Fig. E).

3. The saw cut is not smooth (frayed)

• The saw blade must be sharpened.

• The saw blade has been assembled back-to-

front.

• The saw blade has become coated with resin

or sawdust.

• The saw blade is not suitable for this process.

4. The workpiece is touching the back of the

saw blade and is jumping out

• The riving knife must be aligned (Fig. E).

• The fence is not being used.

• The saw blade is thicker than the riving knife

or the riving knife is not being used

• The saw blade must be sharpened.

• The workpiece has not been kept in its place

until after sawing.

• The tension button of the cross-cut fence is

loose.

5. The height and/or mitre handle is blocked

• Sawdust and dust must be removed.

6. The engine has difficulty reaching the

maximum number of revolutions

• The extension cable is too thin and/or too

long.

• The mains voltage is lower than 230 V.

7. The machine is vibrating

• The machine has not been fastened onto the

workbench.

• The frame is not level with the floor.

• The saw blade has been damaged.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly

clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation

slots free from dust and dirt. If the dirt does not

come off use a soft cloth moistened with soapy

water. Never use solvents such as petrol,

alcohol, ammonia water

, etc.

These solvents may

damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact your local Ferm dealer. In the

back of this manual you find an exploded view

showing the parts that can be ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Warranty

The warranty conditions can be found on the

separately enclosed warranty card.

Ferm

Tverrsaging med loddrett gjæring

Denne sagemetoden er i praksis samme metode

som tverrsagingen, bortsett fra at sagbladet stilles til

ønsket vinkel.

Tverranslaget må bare plasseres på

høyre side av sagbladet. Du må aldri

sage små stykker tre. Ikke bruk hendene

til å utføre vanskelige handlinger!

Tverrsaging med vannrett gjæring

Ved denne sagemetoden må tverranslaget

blokkeres i ønsket vinkel. Hold arbeidsemnet godt

fast, og trykk det mot tverranslaget og bordet før du

begynner å avkorte arbeidsemnet.

5. VEDLIKEHOLD

Sørg for at maskinen er spenningsløs når

det skal utføres vedlikeholdsarbeid på de

mekaniske delene.

Maskinene er konstruert slik at de kan fungere uten

problemer med et minimum av vedlikehold. Hvis

maskinen rengjøres regelmessig og behandles på

riktig måte, bidrar dette til å gi maskinen en lang

levetid.

Feilsøking

Hvis maskinen ikke fungerer riktig, kan du gå

gjennom følgende mulige årsaker med tilhørende

løsninger for å forsøke å korrigere problemet:

1. Motorn starter ikke

• Støpslet er ikke satt i kontakten.

• Det er brudd på strømtilførselen.

2. Arbeidsemnet klemmens inn av spaltekniven

under sagingen

• Juster sagbladet (Fig. E).

3. Sagskjæret er ikke jevnt

• Sagbladet må skjerpes.

• Sagbladet er montert i omvendt rekkefølge.

• Sagbladet er tilsmusset med harpiks eller

sagmugg.

• Sagbladet er ikke egnet for typen bearbeiding.

4. Arbeidsemnet kommer inntil baksiden av

sagbladet og spretter opp

• Spaltekniven må justeres (Fig. E).

• Lengdeanslaget er ikke benyttet.

• Sagbladet er tykkere enn spaltekniven, eller

spaltekniven er ikke benyttet.

• Sagbladet må skjerpes.

• Arbeidsemnet er ikke holdt på plass til etter

sagingen.

• Spennknappen til tverranslaget sitter løst.

5. Armen for høyde- og/eller gjæringsinnstilling

er blokkert

• Fjern sagmugg og støv.

6. Motoren har vanskelig for å nå maksimalt

omdreiningstall

• Skjøteledningen er for tynn og/eller for lang.

• Nettspenningen er lavere enn 230 V~.

7. Maskinen vibrerer

• Maskinen er ikke skrudd fast til arbeidsbenken.

• Understellet står ikke vannrett på gulvet.

• Sagbladet er skadet.

Rengjøring

Rengjør maskinhuset regelmessig med en myk klut,

helst etter hver bruk. Sørg for at

ventilasjonsåpningene er fri for støv og skitt.

Hardnakket skitt fjernes med en myk klut som er

fuktet med såpevann. Bruk ikke løsemidler som

bensin, alkohol, ammoniakk o.kl. Slike stoffer

skader kunststoffdelene.

Smøring

Maskinen trenger ikke ekstra smøring.

Feil

Hvis det oppstår feil som følge av for eksempel

utslitte deler, skal du kontakte serviceadressen på

garantikortet. Bakerst i denne bruksanvisningen

finner du en splittegning som viser deler som kan

bestilles.

Miljø

For å unngå transportskader leveres maskinen i

solid emballasje. Emballasjen er i den grad dette er

mulig fremstilt av resirkulerbart materiale. Benytt

derfor anledningen til å resirkulere emballasjen.

Defekte og/eller kasserte elektriske eller

elektroniske apparater må avhendes ved

egnete returpunkter.

Garanti

Garantibetingelsene er å finne på det vedlagte

garantikortet.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1011 - FZT-250EN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 32,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1011 - FZT-250EN Manual

Product: