Manual Ferm TSM1011 - FZT-250EN (page 10 of 38) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

634097

Zoom out

Zoom in

1/38

Ferm 67

BORDSAV

Brugsanvisningen til elektriske

maskiner skal altid gennemlæses før

brug. På den måde får du bedre

kendskab til produktet og undgår

unødige risici. Gem denne

brugsanvisning et sikkert sted til senere

brug.

Indhold

1. Tekniske specifikationer

2. Sikkerhedsforskrifter

3. Montage og indstillings forskrifter

4. Arbejdsanvisninger

5. Vedligeholdelse

1. TEKNISKE

SPECIFIKATIONER

Beskrivelse

Fig. A

1. Beskyttelseskappe

2. Længdeanslag

3. Indsats til bord

4. Arm til geringsindstilling

5. Arm til højdeindstilling

6. Måleanordning til længdeanslag

7. Til/fra-afbryder

8. Termisk sikring

9. Arbejdsbord

Kontroller maskinen, løsdele og tillbehør for

transportkade.

2. SIKKERHEDSFORSKRIFTER

Forklaring til symboler

Risiko for personskade eller

beskadigelse af materiale.

Angiver elektrisk spænding. Kontroller

altid om netspændingen svarer til

værdien på typeskiltet.

Særlige sikkerhedsforskrifter

1. Ved brug af savblade med tænder af hærdet

metal anbefales det at anvende blade med

negativ eller moderat positiv skærevinkel.

Brug ikke savblade med dybt udskårne

tænder, da disse kan gribe

beskyttelseskappen.

2. Pas på: Montér først alle delene omhyggeligt,

inden du påbegynder arbejdet. Følg den

angivne fremgangsmåde.

3. Når du ikke er fortrolig med at arbejde med en

sådan maskine, anbefales det, at du lader dig

underrette om maskinens virkemåde af

fagfolk, en instruktør eller teknikker.

4. Arbejdsemnet skal altid klemmes eller trykkes

fast mod savføringen, inden bearbejdningen

udføres. Anvendelsen af alle mulige slags

klemanordninger foretrækkes frem for kun at

bruge hænderne til at klemme arbejdsemnet

fast med.

5. Vigtigt: Når arbejdsemnet fastholdes med

hænderne under bearbejdningen, skal

afstanden til savbladet være mindst 100 mm.

6. Tryk altid arbejdsemnet mod bordet.

7. Sørg for, at savbladet altid er skarpt og

kontrollér regelmæssigt, at bladet roterer frit

uden udsædvanlige svingninger. Hvis dette ikke

er tilfældet, skal savbladet udskiftes om muligt.

8. Lad maskinen dreje frit, indtil det maksimale

omdrejningstal er opnået, inden

bearbejdningen påbegyndes.

9. Sørg for, at ventilationshullerne på bagsiden

og undersiden af bordsavbænken og

elektromotoren altid er fri for støv. Dette øger

maskinens levetid. Ophobning af støv skal

undgås.

10.Lås altid de forskellige gradindstillinger, inden

bearbejdningen påbegyndes.

11.Køb udelukkende tilpassede savblade, der er

egnet til et omdrejningstal på mindst 6.000

o./minut.

12.Brug kun savblade, der er egnede til

savbænken. Det er meget farligt at anvende

Spœnding 230-240 V

Frekvens 50 Hz

Optaget effekt 1500 W

Omdrejninger, ubelastet 4500/min

Savklinge 254x16x2,8mm

Tænder Z40

Bordmål 667x430 mm

Vœgt 37 kg

Lpa (lydtryk) 99,3 dB(A)

Lwa (lydeffekt) 112,3 dB(A)

Vibrationsværdi 1,16 m/s

Ferm

4. Is the protective cap working properly?

5. Are you wearing safety goggles?

6. Is the saw blade not rubbing against

anything?

It is absolutely necessary to take these

points into consideration before you

start work!

Lengthwise sawing

• Secure the fence to the correct measuring

position and remove the cut-off guide from the

bench carriage.

• Turn the saw blade approximately 2 mm

higher than the total thickness of the wood to

be sawn.

• Press the wood lightly towards the bench and

let it glide against the cut-off fence.

Remain at least 3 cm. from the front of

the saw blade before you switch on the

engine. The side of the wood which is

against the fence must be completely

straight. Keep your hands at least 10

cm away from the saw track to be

followed.

• Switch on the engine and wait until the saw

blade has reached the maximum number of

revolutions before you start sawing.

• While you press the wood against the bench

and the fence, you can carefully push the

wood through the saw blade without forcing it.

• Never pull the workpiece backwards. If

necessary, switch off the engine first without

altering the position of the workpiece.

Lengthwise sawing with a(vertical) mitre

This method is practically the same, except that

the saw blade is placed at the angle required.

With this type of method the fence may

only be along the righthand side of the

sawblade.

Lengthwise sawing of narrow workpieces

Assume that this process is extremely

dangerous.

Take all the necessary safety measures and

continually push the workpiece through (until

behind the saw blade) using a synthetic aid

instead of by hand.

Crosswise sawing

• Remove the fence and apply the cross-cut

fence in the righthand carriage.

• Adjust the height of the saw blade (see

lengthwise sawing).

• Press the workpiece against the cross-cut

fence and keep at least 2,5 cm distance from

the front of the saw blade.

• Switch on the engine and wait until the

maximum number of revolutions has been

reached.

• Press the workpiece against the fence and

the bench. Carefully push the wood through

the saw blade. Continue until behind the saw

blade. Then switch off the engine and keep

this position until the saw blade has stopped

completely before you remove the wood.

• Never pull the wood back. If necessary, switch

the engine off and keep the position until the

saw blade has stopped completely.

Crosswise sawing with a vertical mitre

This method is practically the same, except that

the saw blade is placed in the angle required.

Only place the cross-cut fence on the

righthand side of the saw blade. Never

saw too small pieces of wood. Never

use your hands to carry out difficult

operations.

Crosswise sawing with a horizontal mitre

With this method the cross-cut fence must be

secured at the angle required. Keep the

workpiece pressed firmly against the cross-cut

fence and the bench before you start cutting off.

5. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Malfunctions

In the case that the machine is not functioning

properly, we give a number of possible causes

and appropriate solutions below

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1011 - FZT-250EN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 32,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1011 - FZT-250EN Manual

Product: