634097

Ferm TSM1011 - FZT-250EN Manual

7
Zoom out
Zoom in
Previous page
1/38
Next page
Ferm 07
11.Only buy suitable saw blades with a number
of revolutions of at least 6000 revolutions per
minute.
12.Only use the correct saw blade. Too small or
too big saw blades are extremely dangerous.
13.Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14.Grease the new saw blade and clean the
flanges before you assemble the new blade.
Then assemble the blade in the correct
direction and pull the flanges firmly using the
central bolt.
15.Only use original flanges. All other types are
not suitable.
16.Never work without the protective cap of the
saw blade.
17.The moving part of the protective cap must
also remain assembled.
18.Never grease the saw blade while it is
rotating.
19.Always keep your hands removed from the
track of the saw blades.
20.Never pick up the workpiece by grasping with
your hands along or behind the saw blade.
21.Ensure that the workpiece never touches the
saw blade before the machine has been
switched on.
22.Never process metal or stone sorts with this
machine.
23.Use support aids in order to support long
workpieces.
24.Never use the machine in a dangerous
environment, where inflammable gases or
fluids are present.
25.Never leave the machine unattended without
first disconnecting it from the mains voltage.
26.If you hear abnormal noises, try to trace them
or take the machine to a recognized fitter, or
repair company.
27.If a part is broken or damaged, replace it or
repair it immediately.
28.Never stand in the track of the saw blade but
stand to the left or the right of the saw bench.
29.Your hands must likewise be placed next to
the track of the saw blade.
30.Always use a wooden pole instead of your
hands to push the wood through the saw.
31.Always place the wood at the front of the saw
bench and then push it further back.
32.For mitring only the adjustable guide must be
used and the fence must be removed.
33.
Never use the fence as a linear measure for
cutting off beams.
34.If the saw blade is locked: first switch off the
machine before you attend to the fault.
35.Avoid workpieces hitting back in your direction
by taking the following measures:
• Always use sharp saw blades.
• Do not saw too small workpieces.
• Never release the workpiece before it has
been completely pushed through the saw.
• Always adjust the guide parallel to the saw
blade.
• Never remove the saw protection.
36.Before you continue sawing, ensure that you
are standing firmly and that your hands are in
the required position.
37.Never use thinners to clean the machine.
Only use a damp cloth for cleaning.
38.Do not use saw blades which are damaged or
deformed.
39.Replace table insert when worn.
40.Use only saw blades recommended by the
manufacturer.
41.Take care that the selection of the saw blade
depends on the material to be cut.
42.Connect circular saws to a dust-collecting
device when sawing.
43.Use and correct adjustment of the riving knife
44.Use and correct adjustment of the upper saw
blade quard.
45.Take care when slotting.
Before use, remove the transport protection:
• Disassemble the bottom plate by loosening
the 4 screws.
• Remove the transport protection below motor.
• The handles for height and mitre setting of the
saw blade are located in the transport
protection inside the machine.
• Reassemble the bottom plate.
Switch off the machine immediately when you
discover:
• A defective mains plug or mains lead;
• A defective switch.
• Overheating of the machine.
• Smoke or odeur caused by scorched
insulation.
Electrical safety
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and
personal injury
. Read the following safety
instructions and also the enclosed safety
instructions.
GB
70
Ferm
• Monter de 2 beslag på savbordets hus og
stram dem fast til (Fig. G-8).
• Anbring skubberen i beslagene.
Samling og montering af længdestyring
Fig. D
• Fastgør aluminiumsstyreskinnen (A) til
styreblokken (B).
• Nu kan hele længdestyringen fastgøres til
bordpladen.
• Skub længdestyringen over bordpladen via én
af enderne på styreprofilen (C).
• Indstil aluminiumsstyreskinnen (A) sådan, at
den ender samme sted som enden af
savklingen.
Montage af spaltekniven og
beskyttelsekappen
Fig. E
• Drej savbladet helt op.
• Fjern indsatsen til bordet.
• Monter spaltekniven i den anordning, der er
beregnet til dette formål. Brug hertil
unbrakobolte og spændestykker. Sørg for, at
spaltekniven falder godt i udskæringen (=
spalten).
• Sæt nu indsatsen tilbage i bordet og fastskru
den.
Læg nu et lille bræt mod savbladet og
spaltekniven og kontrollér, at det faktisk
ligger i den samme retning som
savbladet. Hvis ikke, skal
fastgørelsesboltene løsnes og der
tilføjes eller fjernes spændestykker.
• Over savbladet må afstanden mellem
spaltekniven og tandremmen på savbladet
ikke overstige 5 mm ved skæredybden.
• Spidsen af spaltekniven må ikke være mindre
end 5 mm fra tandspidsen, som vist på Fig. D.
Montage af savbladet
Træk først stikket ud af stikkontakten,
før savbladet monteres eller udskiftes.
• Fjern indsatsen fra bordet med en
skruetrækker.
• Drej savens aksel helt op. Fjern møtrikken og
yderflangen fra savens aksel.
• Skub nu savbladet over savens aksel og sæt
møtrikken og yderflangen tilbage på plads.
Fastspænd møtrikken med hånden.
• Brug nu 2 nøgler: en til flangen og en til
møtrikken og spænd dem godt fast.
• Sæt nu indsatsen tilbage i bordet og fastskru
den.
Montering af holderne til skubbestokken
Monter de to holdere til skubbestokken på siden
af maskinen ved hjælp af de medfølgende bolte
og ringe.
Brug af geringsanordningen
Fig. A
Ved at dreje armen på maskinens side, kan
savbladet indstilles til maks. 45° (4).
4. ARBEJDSANVISNINGER
Der er to slags savemetoder:
• Længdesavning
Herved saves arbejdsstykket på langs med
træets masering.
• Savning på tværs eller afkortning
Herved afsaves arbejdsemnet på tværs.
Når materialet er paneltræ, er træets masering
ikke af afgørende betydning. Når en del af
panelets bredde afsaves, kaldes det
længdesavning og når længden afkortes, kaldes
det savning på tværs eller afkortning.
Ved begge savemetoder er det vigtigt,
altid at anvende en af de to anslage.
Sav derfor aldrig uden anslag!
Pås på! Kontroller først følende punkter, inden
savningen påbegyndes:
1. Er savbladet fast monteret?
2. Er alle spærrearmene blokeret?
3. Er længdeanslaget placeret parallelt med
savbladet?
4. Virker beskyttelseskappen korrekt?
5. Bærer du sikkerhedsbriller?
6. Løber savbladet frit?
Det er absolut nødvendigt at kontrollere
disse punkter, før arbejdet påbegyndes.
Længdesavning
• Blokér længdeanslaget i den rigtige
måleposition og fjern afkortningsanslaget fra
bordslæden.
DK
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1011 - FZT-250EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1011 - FZT-250EN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 32,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info