634097

Ferm TSM1011 - FZT-250EN Manual

6
Zoom out
Zoom in
Previous page
1/38
Next page
Ferm 71
• Drej savbladet ca. 2 mm højere end den
totale tykkelse af det arbejdsemne, der skal
saves.
• Tryk træet let mod bordet og lad det glide
mod afkortningsanslaget.
Ophold dig mindst 3 cm fra savbladets
forside, inden du starter motoren.
Kanten af træet, skal værelige. Hold
hænderne mindst 10 cm bort fra
savsporet, der skal følges.
• Start motoren og vent til savbladet har nået
det maksimale omdrejningstal, inden
savningen påbegyndes.
• Mens du trykker træet mod bordet og
længdeanslaget, kan træet skubbes let
gennem savbladet uden at forcere.
• Træk aldrig arbejdsemnet tilbage. Om
nødvendigt, standses motoren først uden at
ændre arbejdsemnets position.
Længdesavning med (lodret) gering
Denne savemetode er praktisk den samme
metode som længdesavning bortset fra, at
savbladet indstilles i den ønskede vinkel.
Ved ovennævnte savmetoder ma
længdesavning bortset fra, at savbladet
instilles i den ønskede vinkel
Længdesavning af smalle arbejdsemner
Der gøres opmærksom på, at denne
bearbejdelse er meget farlig.
Sørg for, at alle nødvendige
sikkerhedsforanstaltninger overholdes. Skub altid
arbejdsemnet igennem saven (indtil det har
passeret savbladet) ved hjælp af et hjælpestykke
af plast i stedet for med hænderne.
Savning på tværs
• Fjern længdeanslaget og anbring
tværsanslaget i den højre slæde.
• Indstil savbladet i den rigtige højde (se
længdesavning).
• Tryk arbejdsemnet mod tværsanslaget og
hold mindst 2,5 cm afstand fra savbladets
forside.
•
Start motoren og vent til maskinen har nået
det maksimale omdrejningstal.
• Tryk arbejdsemnet mod anslaget og bordet.
Skub træet langsomt gennem savbladet. Bliv
ved med at skubbe, indtil arbejdsemnet er
bag savbladet. Stands dernæst motoren og
ændr ikke denne position, indtil savbladet står
helt stille, før du fjerner træet.
• Træk aldrig træet tilbage. Om nødvendigt,
stands først motoren og bliv i denne position,
indtil savbladet står helt stille.
Savning på tværs med lodret gering
Denne savemetode er praktisk den samme
metode som savning på tværs bortset fra, at
savbladet indstilles i den ønskede vinkel.
Anbring tværsanslaget kun på
savbladets højre side. Sav aldrig små
stykker træ. Brug aldrig hænderne til at
udføre vanskelige handlinger!
Savning på tværs med vandret gering
Ved denne savemetode er det nødvendigt at
blokere tværsanslaget i den ønskede vinkel. Hold
arbejdsemnet godt fast og tryk det mod
tværsanslaget og bordet, inden du begynder med
at afkorte arbejdsemnet.
5. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under
strøm, når der udføres
vedligeholdelsesarbejder på
mekanikken.
Maskinerne er udviklet til at fungere lœnge uden
problemer med et minimum af vedligeholdelse.
Ved at rengøre maskinen regelmœssigt og
behandle den korrekt, bidrager De til en lœngere
levetid for maskinen.
Fejlfinding
Hvis maskinen ikke fungerer hensigtsmæssig,
kan du gennemgå følgende mulige årsager og
tilhørende løsninger for at afhjælpe problemerne.
1. Motoren starter ikke
• Stikket er ikke sat til i stikkontakten.
• Der er en afbrydelse i kablet.
2. Under savningen klemmes arbejdsemnet
ind af spaltekniven
•
Savbladet skal justeres (Fig. E).
3.
Savskæret er ikke jævnt
DK
06
Ferm
TABLE SAW
Always read the instruction for electrical
products carefully before use. It will
help you understand your product more
easily and avoid unnecessary risks.
Keep this instruction manual in a safe
place for future use.
Contents
1. Technical specifications
2. Safety instructions
3. Assembly instructions
4. Operation
5. Maintenance
1. TECHNICAL
SPECIFICATIONS
Product information
Fig. A
1. Protective cap
2. Fence
3. Bench inlay
4. Mitre handle
5. Height handle
6. Measurement set-up for fence
7. On/off switch
8. Thermic safety switch
9. Workbench
Check first whether or not the delivery has been
damaged by transport and/or whether all the
parts are present.
2. SAFETY INSTRUCTIONS
Explanation of symbols
In this manual and/or on the machine the
following symbols are used:
Denotes risk of personal injury, loss of
life or damage to the tool in case of
non-observance of the instructions in
this manual.
Denotes risk of electric shock! Always
check that the power supply
corresponds to the voltage on the rating
plate.
Additional safety instructions
1. When using the saw blades with hard metal
teeth (Carbon tipped) it is advisable to use
blades with a negative or slightly positive
cutting angle. Do not use any saw blades with
deeply cut teeth. They can grip the protective
cap.
2. Attention: First carefully assemble all the parts
before starting work. Follow the procedure as
indicated.
3. If you are not familiar with using such a
machine, you would be better to be informed
first by a professional, an instructor or by a
technician.
4. Always clamp or press the workpiece firmly
against the saw guide, before you carry out
the process. The use of all possible clamping
set-ups is preferable to using your hands.
5. Important: If you are holding the workpiece by
hand for the process to be carried out, keep a
minimum distance of 100 mm from the saw
blade.
6. Always press the workpiece against the
bench.
7. Keep the saw blade sharp and check
regularly whether it rotates freely without
abnormal vibrations. Replace the saw blade if
necessary.
8. Allow the machine to rotate freely until it
reaches the maximum number of revolutions,
before you start the process.
9. Maintain the air inlets at the back and the
bottom of the bench saw machine and electric
engine for a longer machine life. Dust piles
must be removed.
10.
Always lock the dif
ferent degree set-ups
before you start processing.
Voltage 230-240 V
Frequency 50 Hz
Power input 1500 W
No load speed 4500/min
Saw blade dimensions 254x16x2.8mm
Number of teeths Z40
Measurements of bench 667x430 mm
Dust extraction outlet 30 (20) mm
Weight 37 kg
Lpa (sound pressure level) 99.3 dB(A)
Lwa (sound power level) 112.3 dB(A)
Vibration 1.16 m/s
2
GB
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TSM1011 - FZT-250EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1011 - FZT-250EN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 32,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info