Manual Ferm TDM1005 - FTB 16 (page 8 of 42) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

632661

Zoom out

Zoom in

1/42

Ferm 77

• Borepatronens tandkrans må kun fastspændes med den nøgle, der er bestemt til dette

formål.

• Lad aldrig nøglen til borepatronen sidde i borepatronen! Kontrollér, at nøglen faktisk er

fjernet, inden maskinen tændes.

• Brug ikke bor, hvis hals er beskadiget.

• Boremaskinen er ikke egnet til fræsning!

• Når netledningen er beskadiget, må den kun udskiftes med en tilsvarende netledning.

Maskinen skal øjeblikkeligt slukkes i til fælde af:

• Defekt netstik, netledning eller beskadigelse af ledning;

• Defekt kontakt;

• Gnistdannelse i kullene eller ringild i kollektoren;

• Røg eller lugt fra sveden isolering.

Elektrisk sikkerhed

Maskinens elektriske installation opfylder normerne. Reparationer må kun udføres af en

autoriseret elektriker.

Maskinen er udstyret med en nulspændingsomskifter. Når spændingen bortfalder

ved strømsvigt, tilkobles maskinen af sikkerhedsgrunde ikke længere automatisk.

Maskinen skal derfor tændes på ny.

Ved udskiftning af ledninger og stik

Kasser gamle ledninger og stik, så snart de er skiftet ud med nye. Det er farligt at sœtte et stik fra

en løs ledning i en stikkontakt.

Ved brug af forlœngerledninger

Brug udelukkende godkendte forlœn gerledninger, der er beregnede til maskinens effekt.

Lederne skal have et gennemsnit på mindst 1,5 mm

. Hvis forlœngerledningen sidder på en

tromle, rulles ledningen helt af.

3. MONTAGE

Montage

Fig.B

• Bundpladen (12) opstilles på den rigtige plads.

• Søjlen (11) fastgøres på bundpladen med de bolte, der fulgte med maskinen.

• Holderen for bordet (7) med bordet skydes over søjlen. Bordet fastgøres med låsestangen

i den ønskede position.

• Nu monteres maskinhuset og sikres ved hjælp af sikringstifterne.

• Borespindlen er smurt fra fabrikken. Derfor anbefales at lade maskine løbe i laveste gear i

ca. 15 minutter.

Før borehovedet med stiften stikkes ind i borespindlen, skal borespindlens indre

være helt fri for fedt!

FIN

08 Ferm

Setting up the bench drill

Before use the drill must be mounted on a fixed base. The footplate (12) has therefore been

provided with drilling holes. By means of screws the footplate can be fixed to the base in this

place. If it is mounted on a wooden board, sufficiently large washers must be used on the

opposite side, so that the bolts are not pushed into the wood and the machine cannot become

loose.

The fastening screws may be fastened so far that the footplate is not under tension

or deformed. When the tension is too high there is a risk of breakage.

Adjusting the number or revolutions of the drill spindle

Fig.C + D

The different revolutions of the drill spindle can be adjusted by shifting the V-belt into the belt

drive. The machine is protected by a safety switch so that the machine is automaticly switched

off when opening the casing. The V-belt is shifted as follows:

• Open the V-belt cover (14) by loosen the screw on the right side of the cover.

• Loosen the fastening button (4) and slide the engine in the direction of the machine head,

upon which the V-belt is released.

• Shift the V-belt according to the table on the inside of the V-belt cover.

• Tension the V-belt again by pushing the engine plate (15) to the back. Then the tensioning

device is fastened with the fastening button (4).

• Close the V-belt cover and the machine is ready again for use.

Keep the V-belt cover closed during use.

If you have shifted the V-belt, you must tighten it again by means of the engine plate (15) with

the fastening button (4). The tension is correct when the V-belt can be pressed in by

approximately 1 cm. The engine pulley must be aligned horizontally, so that early wear and

loosening of the V-belt can be prevented. For this purpose the engine pulley (13) on the engine

can be slid along the engine axle, after loosening the socket head screw.

Spindle speeds

Fig.E

Position V-belt / Revolutions/min

1) A-4 / 220 5) B-3 / 530 9) D-3 / 1400

2) A-3 / 300 6) C-4 / 580 10) C-1 / 1500

3) B-4 / 350 7) B-1 / 800 11) D-2 / 2200

4) A-2 / 450 8) C-2 / 1300 12) D-1 / 2450

The number of revolutions of the drill spindle of the V-belt combinations can be read from the

illustration and the table.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TDM1005 - FTB 16 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TDM1005 - FTB 16 Manual

Product: