Manual Ferm TDM1005 - FTB 16 (page 7 of 42) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

632661

Zoom out

Zoom in

1/42

Ferm 07

• Only tighten the toothed ring drill holder by means of the wrench.

• Never leave the wrench of the drill holder in the drill holder! Before switching on the

machine, check whether the wrench really has been removed!

• Do not use any drills which are damaged on the shank.

• Drill is not suitable to use as press!

• If the mains cable is damaged, it may only be replaced by a mains cable of the same type.

Immediately switch OFF the machine when:

• Interruption in the mains plug, mains lead or mains lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

Electrical installation

The machine is provided with an electrical installation, which meets the standards. Repairs

may only be carried out by a recognised professional.

The machine is provided with a zero voltage switch. After the tension drops the

machine will not start to run automatically for safety reasons. The machine must be

switched on again.

Electrical safety

Always check that the power supply corresponds to the voltage on the rating plate.

Replacing cables or plugs

Immediately throw away old cables or plugs when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the power input of the machine. The

minimum conductor size is 1.5 mm

. When using a cable reel always unwind the reel

completely.

3. ASSEMBLY

Assembly

Fig.B

• Place the footplate (12) in the correct position.

• Fasten the column (11) with the bolts supplied to the footplate.

• Now slide the table holder (7) with the table over the column. With the fastening handle the

table is fastened into the desired position.

• Now you can assemble the machine casing and lock with the locking pins.

• Since the drill spindle is greased in the factory, it is advisable to run in the machine for

approximately 15 minutes at the lowest speed.

Before you push the chuck with pin into the drill spindle, the inside of the chuck must

be completely grease-free!

FIN

78 Ferm

Opstilling af bæankboremaskinen

Inden boremaskinen anvendes, skal den monteres på et fast underlag. Til dette formål har

bundpladen (12) forborede huller, der er beregnet til montering af bundpladen med skruer til

underlaget. Når bundpladen monteres på en træplade, skal der på den modsatte side bruges

tilstrækkeligt store underlagsskiver for at sikre, at møtrikkerne ikke trykkes ned i træet og

maskinen ikke kan løsne sig.

Skruerne må fastspændes kun så meget, at bundpladen ikke spændes eller

deformeres. Hvis der er for meget spænding, er der risiko for brud.

Indstilling af borespindlens omdrejningstal

Fig.C + D

Borespindlens forskellige omdrejningstal kan indstilles ved at omstille kileremmen i

kileremsdrevet. Inden omdrejningstallet indstilles, skal maskinen slukkes og stikket skal

trækkes ud af stikkontakten. Gør følgende for at omstille kileremmen:

• Stikket skal trækkes ud af stikkontakten, før kileremmens hus (14) åbnes!

• Låseknappen (4) løsnes og motoren skydes i retning af maskinhovedet, hvorefter

kileremmen frigøres.

• Kileremmen omstilles i henhold til tabellen på indersiden af dækslet over kileremmen.

• Kileremmen spændes på ny ved at trykke motorpladen (15) tilbage. Dernæst fastklemmes

spændeanordningen med låseknappen (4).

• Kileremmens hus lukkes og stikket sættes til i stikkontakten. Maskiner er igen klar til brug.

Sørg for, at kileremmens hus er lukket, når maskinen er i drift.

Når du har ændret kileremmens position, skal kileremmen spændes igen ved hjælp af

motorpladen (14) og låseknappen (4). Den rigtige spænding er opnået, når kileremmen kan

trykkes ned ca. 1 cm s. Motorremskiven skal justeres horisontalt således, at alt for tidlig slitage

undgås og kileremmen ikke kan løsnes. Til dette formål kan motorremskiven (13) på motoren

forskydes langs motorakslen, efter at sekskantskruen er løsnet.

Borespindels omdrejningstal

Fig.E

Kileremmens position / Omdrejningstal min

1) A-4 / 220 5) B-3 / 530 9) D-3 / 1400

2) A-3 / 300 6) C-4 / 580 10) C-1 / 1500

3) B-4 / 350 7) B-1 / 800 11) D-2 / 2200

4) A-2 / 450 8) C-2 / 1300 12) D-1 / 2450

Borspindelens ulike turtall og de ulike plasseringskombinasjonene for kilereima kan avleses i

tabellen og illustrasjonen nedenfor .

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TDM1005 - FTB 16 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TDM1005 - FTB 16 Manual

Product: