Manual Ferm SGM1025 (page 8 of 40) (English, German, Dutch, French)

812760

Zoom out

Zoom in

1/40

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with astandardized test given in

EN60745; it may be used to compare one tool

with another and as apreliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories,

may significantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

Description

The numbers in the text refer to the diagrams on

page 2-4.

1. Nozzle nut

2. Nozzle head

3. Nozzle

4. Spray unit

5. Trigger

5a. Lock

6. Motor unit

7. Screws

8. Air filter cover

9. Air filter

10. Container

11. Riser pipe

12. Spray volume adjusting wheel

13. Cleaning brush

14. Cleaning needle

15. Measuring cup

16. Replacement air filter

17. Hanging hook

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Connecting the motor unit to the spray unit

(Fig. A)

• Move the Δ mark on the spray unit (4) to the

(lock symbol) mark on the motor unit (6). Turn

the spray unit (4) until the Δ mark on the spray

unit (4) locks into the (lock symbol) mark on the

motor unit (6).

Disconnecting the motor unit and spray unit

(Fig. A)

• Unlock the lock (Fig 5a). Turn the Δ mark on

the spray unit (4) to the (lock symbol) mark on

the motor unit (6) to separate the two units.

Connecting and disconnecting the container

to the spray unit (Fig. A)

• To connect: Align the container (10) with the

spray unit (4) and insert the riser pipe (11) and

tighten.

• To disconnect: Loosen the container (10) from

the spray unit (4).

Replacing the nozzle (Fig. A)

The nozzle will be assembled on the spray gun

when taken out of the box. To replace the nozzle

follow the following steps.

• Loosen the nozzle nut (1) and remove it.

• Take out the nozzle head (2) and nozzle (3)

from the machine.

• Take the desired nozzle (3) and attach it to the

nozzle head (2).

• Place the nozzle head (2) and nozzle assembly

back in the spray unit.

• Close it by tightening the nozzle nut (1).

4. OPERATION

Preparing the spray gun for use

Step 1: Viscosity/diluting of the paint

This appliance can process spray materials up to

max. 70 DIN/sec (viscosity).

Low-viscosity coating substances, water- and

solvent based paints, finishes, primers,

2 component paint, clear finishes, staining sealers

and wood sealer preservatives often do not need

diluting.

High-viscosity Wall paints, thick varnishes and

thick stains often do need diluting.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm SGM1025 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm SGM1025 Manual

Product: