Manual Ferm SGM1025 (page 10 of 40) (English, German, Dutch, French)

812760

Zoom out

Zoom in

1/40

Always let the paint/varnish/stains dry according

to the recommend dry time of the spray material

for applying multiple coats. Several light coats

rather than one thick coat will help prevent the

paint running.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine.

Cleaning after each use

It is essential that the spray gun is cleaned

thoroughly after every use. Failure to clean it will

almost certainly result in blockages and it may

not operate the next time. The guarantee does

not cover asprayer that has not been properly

cleaned by the user.

The following action must be taken after every use:

1. Empty any unused paint from the paint

container (10). Never leave paint to dry in the

unit (container, riser pipe, needle, nozzle), as

dried paint will prevent the spray gun from

functioning properly. Failure to observe this

important cautionary measure will void the

guarantee.

2. Clean the container thoroughly with the thinner

solvent you have used.

3. Put alittle thinner solvent into the container

and spray until only clean, thinner solvent exits

the spray gun.

Be aware of your surroundings when

spraying outside, wind can cause

unintentional spraying of your not

covered surroundings.

4. Clean the gasket and riser pipe (11) with

thinner solvent.

5. Clean the nozzle and remove all remaining dirt

or paint.

- Remove the nozzle nut (1), nozzle head

(2), Nozzle (3) like explained in chapter

replacing the nozzle.

- Clean all the nozzle parts thoroughly, do not

let them soak in any cleaning detergent or

water.

6. If the cylinder hole becomes blocked, use

asuitable cylinder cleaning needle.

7. Keep the ventilation slots of the device clean

to prevent the motor from overheating.

8. The ventilation slots must be free from dust

and dirt. If the dirt cannot be removed, use

asoft cloth dipped in soapy water. Never use

solvents such as benzene, alcohol, ammoniac

etc. These solvents may attack the plastic

elements.

9. The air filter (9) must be free from dust and dirt.

Ones in awhile you need to clean the air filter.

Remove the air filter like explained in chapter

“cleaning and replacing the air filter”.

10. Clean the outside of the machine. Clean

plastic parts with asoft, clean cloth, preferably

after each use.

Do not use aggressive cleansers (solvents or

abrasive cleansers), or an abrasive sponge or

sharp objects.

Do not put or immerse product in water

or any other liquid.

Always read the precautions laid down by the

paint/varnish manufacturer.

• Do not use liquids containing abrasive

substances such as red lead oxide, glazes,

caustic, and alkaline substances. The use of

these liquids can lead to excessive wear or

corrosion to the pump assembly.

Cleaning/replacing the air filter (Fig. A2)

• Loosen the screw (7) on the backside of the

machine.

• Remove the air filter cover (8) and take out the

air filter (9).

• Clean the air filter (9), always make sure it is

dry before placing it back.

• Place the dry air filter/replacing air filter back in

the motor unit (6).

• Place back the air filter cover (8) and tighten

with the screws (7).

Note: If necessary, replace the air filter (9) with the

replacement air filter (16).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm SGM1025 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm SGM1025 Manual

Product: