Manual Ferm PGM1012 (page 7 of 56) (English, German, Dutch, French, Polish, Swedish, Spanish, Finnish)

632697

Zoom out

Zoom in

1/56

Ferm

• Remove the air filter cover (16).

• Remove filter element and wash well in

solvent.

• Pour a small amount of oil onto the filter

element and gently squeeze out any excess

oil.

• Replace the filter element and air filter cover.

• Be sure the filter cover seals properly all

around.

Do not run the engine without the air filter

element in place.

Never place a wet filter (with solvent) on

the machine.

Fuel tap

• To remove the fuel tap filter, simply undo the

cup at the bottom of the fuel tank

• Use a small spanner to remove the tap

• Clean and wash out the filter and cup, and

replace.

Troubleshooting

Basic checks

• Make sure you have plenty of fuel

• Make sure the fuel tap is on

• Make sure the engine-switch is on

• Make sure the oil level is correct

• The generator has an oil sensor. When the oil

level is too low, the generator will not be able to

start.

• Remove spark plug, connect spark plug lead

and earth it to the generator. Pull starter cord

gently and look for a spark. If there is no spark,

replace spark plug.

Spark plug is OK, but engine still won’t start

• Check fuel tap filter is clean

• Check fuel line is clear

• Check carburetor is not clogged

Engine will not start

• Clean or replace spark plug

• Check ignition system – if faulty, contact your

service centre

• Check compression – if low, contact your

service centre

• Check for loose cylinder head – tighten bolts

• Check for damaged cylinder head gasket –

replace if necessary

Cleaning

Clean the housing regularly with a soft cloth,

preferably every time it is used. Keep the air vents

free of dust and dirt.

Remove stubborn dirt with a soft rag moistened in

soapy water. Do not use any solvents such as

petrol, alcohol, ammonia, etc. as such substances

can damage the plastic parts.



• Drain fuel tank, fuel tap, carburetor bowl and

carburetor

• Pour 1 cup of engine oil into the fuel tank and

shake the generator to spread the oil around

the tank. Drain excess oil.

• Remove spark plug and pour in 1 spoonful of

engine oil, pull the starter cord several times

with the starter switch OFF. Replace spark

plug.

• Pull on the starter cord until you feel

compression and stop.

• Clean the generators exterior and coat with

rust inhibitor.

• Place the generator on flat ground and cover

with a clean dry cloth.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the warranty

card. In the back of this manual you find an

exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be collected

at the appropriate recycling locations.



Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/EU

for Waste Electrical and Electronic Equipment

and its implementation into national right, power

tools that are no longer usable must be collected

separately and disposed of in an environmentally

friendly way.



Read the terms of warranty on the separate

warranty card which is enclosed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PGM1012 in the language / languages: English, German, Dutch, French, Polish, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm PGM1012 Manual

Product: