Manual Ferm PGM1012 (page 6 of 56) (English, German, Dutch, French, Polish, Swedish, Spanish, Finnish)

632697

Zoom out

Zoom in

1/56

6 Ferm

• Clean up any spilled fuel

• Do not smoke while operating the generator

Always use caution!

Starting the generator

Fig. 1 + 4 + 5

1. Turn on fuel tap (15).

2. Turn on engine switch (12).

3. Move choke lever (13) to closed position (to

restart a warm engine, leave the choke lever in

open or half-open position).

4. Pull slowly on the starter cord until it engages,

then pull sharply to start the engine (14).

5. Allow the engine to run until it warms up, and

then move the choke lever to the open position

(13).



• Start the generator.

• Plug in the electrical appliance plug.

• Press AC current protector downward to

“ON”(7).

• The voltmeter (11) displays the voltage on the

AC socket. Normally this should be ± 230 V

during use.

Stopping the generator

Fig. 1 + 5

1. Unplug all cords (5)

2. Turn engine switch to “OFF” (12)

3. Turn off fuel tap (15)

4. Service & Maintenance

Periodic maintenance



• Check engine oil level

• Check fuel hose for cracks or other damage.

Replace if necessary.

• Check exhaust-system for leakage. Retighten

or replace gasket if necessary.

• Check choke operation

• Check recoil starter operation

1st Month or 20 hrs

• Replace engine oil



• Check condition of spark plug. Adjust gap and

clean. Replace if necessary.

• Clean, replace if necessary.

6 Months or 100 hrs

• Replace engine oil

• Clean fuel tap and fuel tank filter. Replace if

necessary.

• Check fittings and fasteners. Replace if

necessary.

12 Months or 300 hrs

• Contact a specialized service centre to check

the valve clearance.

• Check the fan of the cooling system for

damage.

Service – notes on maintenance

Fig.1

Oil replacement

• Warm up engine on level ground

• Remove filler cap (8)

• Open drain plug (9) and let oil drain completely

into a pan placed under the engine.

• Check gaskets, replace if required. Refit drain

plug and refill engine with clean oil.

• Replace filler cap.

Spark plug inspection

Fig. 3

• Disconnect the spark plug cap, and remove

any dirt from around the spark plug area.

• Remove spark plug (17) with the plug spanner

supplied.

• Inspect the spark plug. It should be a tan

colour.

• Measure the gap (distance contact point) with

a suitable gauge. The gap should be 0,7 - 0,8

mm. Correct the gap, if necessary, by carefully

bending the side electrode.

• Replace the spark plug if the electrodes are

worn, or if the insulator is cracked or chipped.

• Install the spark plug carefully, by hand, to

avoid cross-threading.

• Place the spark plug with correct torque: 20

Nm.

• Attach the spark plug cap.

Exhaust screen

• Wait for exhaust to cool.

• Exhaust screen may be blocked up with

carbon deposits.

• Undo the screw cap and remove the exhaust

screen.

• Clean the screen with a wire brush and refit.

• Replace exhaust screen if damaged.



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PGM1012 in the language / languages: English, German, Dutch, French, Polish, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm PGM1012 Manual

Product: